Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1325WW02 > Instructions

RVM1325WW02 Hotpoint Microwave - Instructions

All installation instructions for RVM1325WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1325WW02
31-45 of 163
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loss of lighting for over-stove illumination.

  • Customer: ROGER from BLUFFTON, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

Light Socket replacement

  • Customer: Jill from Arlington, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Bulb was stuck in the lamp

  • Customer: lawrence from huntersville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.

door handle broke off

  • Customer: Donald from CHAPIN, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I had to remove the two screws that were still in place from the broken door handle. Once they were removed I placed the new handle on the microwave and screwed the new handle in place. A total of less than 10 minutes!!!

The glass tray that I got from Partselect cracked after a few months of use.

  • Customer: Paula from Mount Laurel, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 12 people found this instruction helpful
The glass tray in my microwave oven cracked and I found PartSelect on line. They sent me a replacement tray quickly. All I had to do was remove the cracked tray and insert the new one. Unfortunately ,after a few months this tray also cracked! I checked the Partselect website and found out my tray was guaranteed for one year ! PartSelect sent me a new tray free of charge. I received the tray in a few days.
Thanks Partselect!

under microwave (above stove) light

  • Customer: Bruce from Cleveland, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).

Cooktop light receptacle cracked

  • Customer: Ronald from Wood Dale, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Bulb burned ot

  • Customer: John from Fort Smith, AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

Microwave handle broke

  • Customer: Rosemary from Roseville, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First mistake I made was assuming the replacement handle would come with screws. It didn't so had to place a second order for the top screw. Make sure you order everything you need. First I popped off small rim on inside of door with the tip of a knife to expose the lower screw. Removed old handle. Set new handle inplace and tightened both top and bottom screw. Replaced rim to original position. And voila! Done. Easy fix if you have all the necessary parts.

After closing door the display panel must be tapped on to keep the unit operating.

  • Customer: Paul from San Jose, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 34 people found this instruction helpful
The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

Left light socket was damaged beyond repair

  • Customer: Kathleen from Streamwood, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Microwave wouldn't start after "Start" pushed

  • Customer: Don from Monte Sereno, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

microwave door handle broke

  • Customer: JOSEPH E from BRICK, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
removed the 2 existing screws, aligned handle with holes, tightened screws.....done

Old handle broke.

  • Customer: James from Smyrna, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
Removed the two screws holding the origional handle to the door. Attached new handle with same two screws. Job completed.
All Instructions for the RVM1325WW02
31-45 of 163