Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1325WW02 > Instructions

RVM1325WW02 Hotpoint Microwave - Instructions

All installation instructions for RVM1325WW02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1325WW02
46-60 of 163
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave would turn on when door opened

  • Customer: Lois from El Segundo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

Lens Was Not Sized To Fit And Was Left Extremely Sharp

  • Customer: robert from salmon, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Handle on microwave fell off

  • Customer: Lynne from Waxahachie, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
There were globs of glue where handle was attached. Glue was brittle and chipped off rather easily. Ordered the new handle which arrived as the exact one needed and in 3 days with the lower cost shipping charge. The screws do not come with the handle but the old screws were still in the door and were removed easily with some needle nose pliers. Cleaned off appliance door and attached new handle in about 5 minutes or less. Used no new glue. A very easy repair.

Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!

  • Customer: Mark from Hanover Park, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 10 people found this instruction helpful
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

microwave would not start

  • Customer: JULIA from JACKSONVILLE, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 10 people found this instruction helpful
took of cover removed switch and replaced with new one

After closing door the display panel must be tapped on to keep the unit operating.

  • Customer: Paul from San Jose, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 29 people found this instruction helpful
The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

Broken Light Socket

  • Customer: Richard from Batavia, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

NO light

  • Customer: Dan from Leesburg, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
.Thank You Dan

Light bulb burned out and assembly broke when trying to replace bulb

  • Customer: Jeanne from Kirkwood, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I used the internet and your directions to complete the repair. It was easy!

Microwave wouldn't start after "Start" pushed

  • Customer: Don from Monte Sereno, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

handle broke

  • Customer: Tom from Cupertino, CA, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
had to use pliers to grab a nub of the plastic screw female that had broken off. Other than that, went easy. This is a product defect and not only should the part be free, but there should be a free retrofit repair.

Your part was here quickly and perfect.

Great job, thank you.

The handle broke off are mirowave oven above are stove!

  • Customer: Kenneth from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
The repair was very simple. All we did was take two screws out and replace the handle and screw the new handle back on. That's it!!!
I thought the part was expensive but considering replacing the microwave it was well worth it!!

Old handle broke.

  • Customer: James from Smyrna, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed the two screws holding the origional handle to the door. Attached new handle with same two screws. Job completed.

door handle broke

  • Customer: FRANKIE from NEW JOHNSONVILLE, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I first removed the broken door handle by removing two screws and replacing it with the new handle.The new handle was the exact size of the old handle,the holes lined-up perfect.I ordered the handle on thurs. and expected to get it the next week. I got the part Sat.

the microwave door handle had broken off leaving the plastic stem in the screw hole

  • Customer: laura from Stamford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I went on the PartSelect page and found the model # for my microwave and ordered the handle. I thought I was going to have to wait for several weeks but it arrived in three days. The only glitch was that the plastic end of the broken handle was still attached to the screw and I couldn't get a grip on it in order to remove the screw...so I tried several different things... ultimately using a corkscrew to pierce the old piece of plastic handle thus allowing me to remove the screw and in two minutes I was able to replace the handle.
I can't believe it was that easy. Thank you.
All Instructions for the RVM1325WW02
46-60 of 163