RS22BRXDN01 Roper Refrigerator - Instructions

Debugged problem according to debug video; ordered part based on most likely part failure; part came in < 2 days; installed part based on installation video. Freezer and fridge both fixed.

removed the damaged unit and inserted the replacement.

My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

I followed the instructions provided on a video that was shown when I went to order the required parts. The video was very well done. It is very accurate.If you fololw the instructions you can make the repain in about 30 minutes. It was very easy

After figuring out online what I needed I was sent the step by step video on what to do. I have never did anything like this but I learned. In the Past my husband would deal with it but he is no longer alive to do this kind of stuff. Thank goodness you sent the video along with all the instructions as i had my laptop on the table and followed stopped it and followed it again. I actually did this . I am so proud of myself.Thank you for making it so easy.

I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.

The Sears man came out and told me it was the thermostat that needed to be replaced and it would cost $321 plus tax. I went on youtube and watched the Partselect video several times and decided to order the part after seeing how easy it was to install. Total cost $65. I put the laptop on the counter and watched it as I installed it. It helped that I could go back and watch a certain part if there was a problem. But I had no problems and installed it in 20 minutes. Very, very simple to do. Of course I had to pay $75 to the Sears man but I saved about $200 . Thanks Partselect.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

Straight forward.Vey easy to do

I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

The replacement ice maker did the trick. Perfect fit for old one. It took about 20 minutes to complete the repair. Directions were clear and easy to follow. It did take about 6 hours for the ice maker to make ice. within 48 hrs the bin was full.

Using a pair of pliers position the nose perpendicular to the inner wall of the ref and grip tight on the flat part of the support stud and twist counterclockwise until it become loose. Once loosened pull the support stud outward until it clears the the hole. Installation: Slide the support stud in and twist it hand tight. Using a vise grip and locking the jaw just tight enough to hold it firm on the flat parallel edges twist them (one at time) clockwise until it feels tight the tongues are parallel to to be able to slide the shelf support.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.