RS22BRXAW00 Roper Refrigerator - Instructions

2 screws...removed old part Module Assembly..put in new and was set to go!

I had to make sure the electronic beam was working properly, which it was (steady beam if you press in the side plastic flap. I also had to make sure the water valve for the icemaker was working properly as well, which it was by switching the lead wires on the valve (water dispenser wire to ice maker valve, and hitting water dispenser paddle and hearing water flow to the ice maker). After that, I knew it was the icemaker motor. Removed three screws with a socket, disconnected wire harness (had to use pliers to pull it apart), pulled out entire icemaker unit. Loosened three screws on motor control unit to remove it from icemaker unit, then inserted new motor control unit and re-screwed the 3 screws. Then I pu tthe entire icemaker unit back in the freezer, connected wire harness, re-inserted three screws and was finished. I then waited for one hour, went to check ice maker and I had ice cubes forming in the tray.

With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Unplugged the refrigerator removed the cover and 3 screws. Pulled the old part off and replaced with the new and screwed it back on. Replaced the cover plugged it back in and it started working again.

I am a woman, not mechanically handy, but set my mind to do this myself. The part came in 2 days. I watched the video and had it in done within minutes. Very easy! A few scews and follow video.

Thermostat replacement

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took the upper three screws pull the door up and then removed the broker part in the bottom of door by removing one screw. Install new part and put door back securing it by the three screws on the top of regrigerator. Very easy

Easy job due to great instruction video by PartSelect.

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

Before I ordered, I followed the great video to disassemble the unit. That's when I realized I only needed to buy the drum. Five days later, I had the part. I thought I remembered how to reassemble it, but I ended up needing to watch the video again. It wasn't difficult, but you must get all the bits back in the same order!! Once that was dine, it all went together easily. Thank you! I'm so impressed with this site that I posted on Facebook about it so my friends can also save big bucks doing simple repairs themselves.