RS22AWXDW00 Roper Refrigerator - Instructions

I watched the instructional video on the website. I found that my model was not exactly the same as the one in the video,completely removing the unit in order to switch parts was not possible or necessary.

Remove drip tray, remove two screws under drip tray and remove trim piece around dispensers. The micro switch is located at top right corner; slide it off the small post that holds it in place. Remove wire from switch (be gentle so you don't break wire, mine was on pretty tight. My switch was clearly burned out (black on connections). Anyway, just click wire back on new switch and push back on the post that holds it in place. Put back trim, screws and drip tray. The whole thing took a few minutes....I am no repair man but there were two switches on the post next to one another, I imagine the other controls the water dispenser in the event it had the same problem? If I had removed the trim piece and looked before ordering the part I probably would have swapped them out to confirm the problem was definitely the switch...I assume you could do that because they appear identical but can't say for sure. However, all indicators pointed to the switch anyway. Part was inexpensive and Part Select got it right out to me.

removed cover unbolted thermo an replaced no big deal

First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

First, I took out the broken unit,yhen I put in the new one..

Unplugged the fridge and removed the cover from the Icemaker control assembly. Then remove the three phillips head screws, remove the Icemaker control. put the new control in place and use the three screws removed in previous step, replace the cover and plug the fridge back in. in a few hours you will have some ice.

Replaced the icemaker control assembly and ice mold. Icemaker is working perfectly now. We replaced the ice mold (tray) because my husband read on the internet that the ice mold loses its nonstick coating and the ice sticks to the mold, and eventually burns out the control assembly.

The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.

This was a very easy repair and only took about 20 minutes. Unfortunately, after reordering, and installing the second motor, the intermittent noise is still there. Other than the occasional buzzing noise, that sounds like it is coming from the evaporator fan area, the refrigerator runs fine.

Simply follow the video instructions. Involves the removal of nine screws. to remove the old plastic sleeve cut the tube near the old thermostat and it slides of easily. Apply dish or hand washing soup to the new tube when putting the plastic sleeve onto the new probe. The hardest part is getting the end of the probe coiled to the right shape. Hey,` if I can do it with a broken collar bone, anybody should be able to do it.

This was a very easy fix. I utilized the short repair video for both parts and the entire install time was 40 min max. I installed both parts per the instructions, plugged the unit in and waited 20-30 minutes for the unit to reset itself. The Fridge cut back on and its running well within guidelines. In fact, it's cooler and running better than the last 6 months. Thank you "Part Select" for helping me save real dollars.

the part was replaced in less than minute

replace drawe

Read the instructions, watched the video and followed the very clear instructions and lay out.

Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.