RS22AWXDW00 Roper Refrigerator - Instructions

When I ordered the new auger drum from this website, I noticed a video that explained how to install the item. When I received the new drum, I went to the website and found the video. All I did was to watch the video and do what the repairman did. I did get a little confused when I noticed that the auger in the video was metal, and mine was plastic. However, upon removing the pieces as shown in the video, it became clear that the new auger drum would fit the same way the broken one had fit. After that, it was a snap to put the pieces back together.

the repair from the video was exact to a tee. Very helpful 100%.

The icemaker is in a side by side refrigerator/freezer with an auger driven ice bin dispenser, so space was limited. I first removed the ice bin but I couldn't see the three nuts holding the icemaker in place. I removed the ice bin support bracket (under the icemaker) using a Phillips head screw driver. Now the bottom nut holding the icemaker in place was easily visible and I was able to determine the size of nut driver I needed to completely remove it. Then I felt for the location of the top two nuts, slipped the nut driver on and loosened them. I was able to lift the icemaker off the top two nuts without completely removing them. Using a flat head screw driver, I pushed down the white tab holding the wiring harness connection to the icemaker and removed the harness, freeing the ice maker for complete removal. I did not need to replace the wiring harness, so I simply reversed the whole process to install the new icemaker. I am a 61 year old female with rheumatoid & degenerative arthritis and found this installation really easy, with the one exception of snapping the wiring harness connection into the new icemaker - I didn't have the thumb strength. I had to wait for a relative to come and snap the wiring harness connector into place for me. I also had to use some snips to cut out the plastic tab (scored) for the water feed to the icemaker but was able to complete the entire installation within 30 minutes.

Took it out and slipped the new one in.

Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.

Unplug the unit cord, remove 3 screws on the icemaker. Unhook the wiring harness from the refrigerator, remove the unit and reverse the order to install the new unit. Reinstall the on off bail, and the icemaker tray. Make sure that the unit is level after the new installation so that water does not spill out of the icemaker.

R and R parts

Removed the broken icemaker per instructions provided with the replacement part purchased. by Part Select. The whole procedure went very well and my new icemaker is working like a charm. I highly .recommend Part Select. Kitchenaid had discontinued making the the original icemaker and Part Select provide an OEM replacement that worked perfectly.

just like video very easy ! Thank you for the fast service and good information for installation.

I ordered both the defrost timer and thermostat thinking the problem was the thermostat but scince the two parts were housed in the same part of the refrigerator I decided to replace both parts. Watching the YouTube video made this job a complete success!! The parts arrived within 24 hours! This girl is a VERY happy customer. Thank you!

just remove the damaged one and replace with the new one---easy- breezy

Ice dispenser guide: Required a screwdriver for one screw and was done in minutes. Part fit was perfect. Door cam kit: shut off water to refrigerator. Remove lower vent and disconnect water line, mine had an in line coupler below the door. I raised the door with a simple car jack and removed all bolts to the door hinge and upper cam on under side of the door. Remove the spring over the hose and slide old pieces off of the line. Feed the new cam piece for door and install the one on the door hinge with supplied bolts and screws. Install hinge and spring back over the line and hinge to the refrigerator. Connect the water hose with the coupler and turn water back on. Cam kit makes door work like new. Replacement of all pieces above mentioned took about an half an hour. Well worth the time and cost. I figure would have cost about $100.00 + to have a repairman do this and I did it for $35.00 in parts.

Just re-intall the new drawer. That's it. Thank you !!

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!