Models > RES7745PQ0 > Instructions

RES7745PQ0 Roper Dryer - Instructions

All installation instructions for RES7745PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RES7745PQ0
1,861-1,875 of 2,011
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer was working fine, just very noisy during operation. wump,wump,wump

  • Customer: Gary from Point Pleasant NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
watched the online video on the Partselect site which was very informative and straight forward. replaced the belt, tensioner, and two drum rollers (all included in the maintenance kit, (along with small hardware parts)). put it all back together, and VIOLA!!!!!! super quiet like the day we bought it!!! Thanks!!!

Broken belt

  • Customer: Michael from North Bellmore NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did as your online movie said to do it. It is a big help and you can see that the belt, rollers and idler pulley is not a difficult job and you save yourself at least $100. Toughest part of job is putting back the nylon triangle things that hold the rollers on without breaking them.That is why I used the needlenose pliers. The triangle things that hold on the rollers have little tabs on them and I just gently pulled them outward and the triangles went right on.That repair kit from Whirlpool(builder of my Kenmore dryer)was a real bargain and everything fit perfectly. Bottom line is don't be afraid to try this repair. You will most likely succede. Go out to diner with the money you saved. Good luck, Mike

Installation of Maintence Kit & Door Latch

  • Customer: Roger from Twinsburg OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Parts were received in one day!!!The instructions were clear, concise and easy to follow. The pictures and figures significantly added to the ease of completing this task.

drum not rotating

  • Customer: Robert G from Dansville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

broken belt and roller

  • Customer: FLOR from Jersey City NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced Broken Belt and roller

Broken Dryer Belt

  • Customer: WILLIAM from DELRAY BEACH FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Loud banging noise from under dryer.

  • Customer: Paul from Pottstown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Drum does not rotate

  • Customer: Richard from Westhope ND
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

the drier belt broke and the tensioner was worn

  • Customer: gerald from coventry RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took off top of drier completely making sure to photograph wiring diagram for timer, then removed front. Laying drier on it's back, I could then install new belt and tensioner without needing a second pair of hands. I tried using bungee cord but found it easier for me to lay drier on its back. I completely vacuumed all areas including back of drier. I found the retainer clips for front of drier to be bent, so I straightened them. I also installed two sheet metal screws in case one of the retainers failed.

Dryer making squealing noise

  • Customer: Natale from Brooklyn NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.

The roller wheels wore out

  • Customer: tim from cincinnati OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Broken belt and replaced rollers

  • Customer: George from Rehoboth Beach DE
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Viewed online video and written instructions that were included in maintenance kit.

Dryer making loud noise on startup and during cycle sometimes.

  • Customer: Kenneth from Raleigh NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the procedure outlined in instructions included with maintenance kit. My dryer did not have a pully wheel on the idler arm. Instead it was more or less a wear bar formed in a semi circle attached to the idler bar. This is what was causing the noise. The dryer wheels were good and the dryer belt was good too after 10 years of use. The parts in the kit were of good quality and fit perfectly. The supplied instructions were easy to follow.

my dryer stopped tumbling

  • Customer: joann from woonsocket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

Sqealing noise and extended drying time

  • Customer: Gregory from Casa Grande AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed online youtube directiond to dissassemble dryer cabinet. Everything is readily accessible and belt and idler are easily installed. Comments from others express frustration at the instability of the idler pulley bracket. The key is to keep seating pressure on bracket until the belt is installed at which time the belt supplies continuous pressure to seat the bracket. The bracket is very stable so long as moderate force is applied to hold the brackett in the seat. The belt install is counter intuitive in that the ribbed side of the belt is installed in contact with the drum instead of the flat side. The readon for this is so the belt ribs seat in the grooves of the motor pully and provide greater friction. Flat side of the belt on the drum places the flat belt on the grooved pulley with much reduced contact area.
All Instructions for the RES7745PQ0
1,861-1,875 of 2,011