RES7745PQ0 Roper Dryer - Instructions

Found an instructional, easy to follow video by PartSelect online. It was helpful to know what tools I needed before beginning the job. I first purchased only the belt. After taking the dryer apart, I saw the idler had also broke. It was very helpful that the parts arrived quickly. The video was the the greatest tool for doing this repair myself!!!!

i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.

Videos say it all . Quick parts delivry .

Unplugged the dryer from the electric outlet; removed the screws from the back panel, removed screws from the unit and pulled down and outward to release the unit. Removed the wires and attached to the new unit. Plugged the dryer in to see if the unit worked. It worked, so I unplugged the electrical cord, replaced the back panel and screwed in the screws.

Removed rear panel and replaced sensor. Sad thing is this was not the problem.It was the coil valves! They are a $20 part together, and I wish I would have replaced them first! There is two of them that are on the main valve for the gas! Remove the front cover of machine. Make sure the gas is off , remove the bracket holding the valves in and this it! Quick simply repair that is where I should have started!

Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

Watched the videos for unusual noise... they are great and saved me time with advice how to open the machine from top and front and install belt on tension wheel. Lower roller bad, replaced both. Opted to also order and replace the belt and rear seal upon inspection. Time spent would have been 30 minutes or less but rear seal replacement requires time to clean off old seal adhesive and glue on new one. Take your time with rear seal replacement it takes longer than I thought but worth it. The labor involved to replace the seal alone would have been more than the dryer cost new. Also- I ordered parts at 2pm std shipping option and got them THE NEXT DAY less than 24 hrs later. May not be typical depending on your location but I was amazed. I have been fixing all my own appliances for years first time customer with Parts Select. Oh and EACH of the 3 parts ordered were 10$ less EACH than my local parts guys. WOW

After checking the PartsSelect website, I found that the most likely cause for my no heat problem was the Thermal Fuse and the Cycling Thermostat. I ordered both since they are located next to each other on the dryer. I followed the instructions in the video, first removing the dryer back. Next I located and removed both parts. I also did a cleaning of the dryer compartment since the back was already removed. Installed the 2 parts according the the video and re-installed the dryer back. It is now running like new. Great website, excellent video instructions saving me $600 to replace a perfectly good working appliance.

I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

I watched the video and did the repair myself. My husband, who works in maintenance, was IMPRESSED! Yay! Thank You!!!! Love you guys! I am forwarding your website to my children!

Thermal Cut-Off Kit (279816) was the wrong part for our Whirlpool Dryer Model. The thermal cut-off replacement part did not match the incumbent part. Before ordering this kit, I would recommend homeowners remove the back of the dryer and verifying this kit would work on their dryer. In our situation, it was a fuse that had to be replaced. Although your kit did not help or address my problem, I found the buying experience and the DIY reassurance to be positive. Hopefully the refund process will be equally positive. Thank you.

Unplug dryer, remove hex screws securing back panel, disconnect plug and conncector from switch, twist and pull out switch; install new switch by reversing the process.

Parts were received in one day!!!The instructions were clear, concise and easy to follow. The pictures and figures significantly added to the ease of completing this task.