Models > RES7745PQ0 > Instructions

RES7745PQ0 Roper Dryer - Instructions

All installation instructions for RES7745PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RES7745PQ0
1,831-1,845 of 1,975
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer made kind of a grinding noise when it started. A repair technician looked at it and said it needed new drum support rollers and shafts.

  • Customer: Janis from Lakewood CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.

drum rollers worn out, making kocking noise

  • Customer: Nita from Clarkston WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Unusual noise

  • Customer: Ingrid from Orland Park IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the videos for unusual noise... they are great and saved me time with advice how to open the machine from top and front and install belt on tension wheel. Lower roller bad, replaced both. Opted to also order and replace the belt and rear seal upon inspection. Time spent would have been 30 minutes or less but rear seal replacement requires time to clean off old seal adhesive and glue on new one. Take your time with rear seal replacement it takes longer than I thought but worth it. The labor involved to replace the seal alone would have been more than the dryer cost new. Also- I ordered parts at 2pm std shipping option and got them THE NEXT DAY less than 24 hrs later. May not be typical depending on your location but I was amazed. I have been fixing all my own appliances for years first time customer with Parts Select. Oh and EACH of the 3 parts ordered were 10$ less EACH than my local parts guys. WOW

Replace Rear Seal on Drum

  • Customer: Elizabeth from Myrtle Beach SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First unplug the unit and move to an area where you will have enough room to pull the drum out. I opened the top by sliding a screwdriver in the top left and right edge and popping the clips to allow the top to lean up and back against the wall. I tried to unclip the harness for the door switch but couldn't get the harness to release and instead took out the two screws holding the door switch in place. This is located on the top right inside the dryer door. Once the switch was off I was able to use the socketdriver to undo the two screws on the inside top left and right to release the front of the dryer by pulling up easily and unhooking the bottom front. I was then able to set the front of the dryer aside and begin removing the belt from the tension wheel and motor. Pay close attention to how the two are connected because it will confuse you putting it back together.The belt feeds through the tension wheel and when you release it the tension wheel is just sitting in place and may pop out of place. Remember which slots it sets back into for when you put the dryer back together. We removed the drum, checked the two rollers to make sure they were in good working order. I removed quite a bit of debris from them. Once the drum was out I pulled off the old seal. Took a piece of sandpaper to rub away any excess old adhesive and began installing the new felt seal. Follow the directions carefully to ensure that the seal is sitting on the edge properly before you begin applying adhesive under the edge. I had someone helping me to install the seal but probably would have needed clamps to hold the seal while working it on. It's not a super tight fit but is fitted and once you start putting it on it easily slips off the other side. A couple clamps would hold it in place if you don't have someone to help. Once the seal is on and you apply the adhesive you begin putting the drum back into place first by slipping the belt back over the drum where it can hang until you are ready to put it back on the motor. You have to make sure the seal isn't folded under the back of the dryer. Again a little tricky but if you gently spin the drum slowly counter clockwise a few times you can work it so it's not folded under. Once you see everything is in place you can reconnect the belt through the tension wheel onto the motor. Check drum again by spinning counter clockwise. Install the front of the dryer back on by setting it into the bottom clips. Put the top screws back in. Re-install the door switch making sure it's back in place with the tab sticking through the hole at the top of the dryer door. Bring the top back down. Close the dryer door and plug it back in and everything should be good to go. It wasn't a difficult job at all and I would probably attempt other repairs now that I've done this one. Beware the adhesive is kind of watery when it comes out but you don't need to use a lot under the edge of the seal. Good luck with your repair. I am thankful that PartSelect was so easy to order my parts from and I got the part within a few days. Thanks!

squeaky dryer and already replaced everything else

  • Customer: Melia from Quincy FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched several Youtube videos for this repair. The best showed a man taking you through every part of replacing the rear felt seal. I used binder clips from my home office and he used clothes pins to keep the seal in place while gluing it and letting it set. To completely finish this repair, it takes over 24 hours to get your dryer ready for drying again. Steps to repair: you need to get to the dryer drum, watch a video on how to do this to include taking off belt, idler pulley. Remove Drum from the dryer. take off all the old felt seal. take out new felt seal and place around the drum, it will be pretty tight. secure the seal by using clothes pins or binder clips all the way around the drum. this will help you keep the seal on the drum and guide you as you use the glue to bind the seal to the drum. Using the adhesive provided with the felt seal, going around the drum, glue down the seal and re-clip it so the glue gets a good grip. let dry of at least 1 hour. Cannot use the dryer for another 24 hours to make sure the glue dries completely and is ready for the heat. I had already replaced the 2 rollers, 2 shafts, belt, idler pulley and start switch and dryer still squeaked. Then I replaced the rear felt seal. NOW I am replacing the bulkhead because it is worn flat in some places and is warped. I am waiting on the part.

Drum seal came apart

  • Customer: Glen from El Paso TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Raised top of dryer and removed screws holing front on. slid front panel up and off to remove drum. Seal was easy to install but you do have to be careful with the adhesive. After adhesive was dry laid dryer on it's back and installed drum. Reinstalled drum belt. Placed front panel back on and installed the two screws holding it in place. Set dryer upright and closed top.

noise due to worn drum wheels

  • Customer: Derek from Wyoming MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
fliped up top, removed 2 5/16 screws from face and removed. removed drum and belt. removed two piece ring bearing and removed front seal from front face. installed new seal and split bearing the way others were removed. reassembled dryer in reverse order.

old lint filter was broken

  • Customer: John from York PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I had to do was take out the broken filter and replace it with the new one. It fit perfectly. The replacement took less than 5 minutes. I should have done it a year ago!!

The clip that holds the plastic handle to the lint screen broke off.

  • Customer: Pat from Zebulon NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new lint screen fit perfectly. All I had to do was slip it in the lint filter slot.

Lint filter was broken

  • Customer: Calvin from Saco ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Tried to replace filter would not fit It was delivered outside and was real cold and stiff after I let it set for awhile it warmed up it fit great. Thank you Calvin

old filter broke

  • Customer: Ellen from Burlington MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out old put in new

Lint filter handle broke

  • Customer: Joan from Dudley MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slid the new lint filter into slot on top of my 26 year-old Kenmore dryer and it fit perfectly! Ordered part and received it the next day...unbelievable!! Definitely A+ service.

Lint Filter mesh was frayed.

  • Customer: Christian from Battle Creek MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Purchased a new lint filter. Delivery and installation were no problems. The easiest repair that I've ever done.

Replaced lint filter

  • Customer: Robert from Palatka FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The part was delivered when promised. Part was a perfect fit. I was very pleased with the entire process.
All Instructions for the RES7745PQ0
1,831-1,845 of 1,975