Models > RAX7244KQ0 > Instructions

RAX7244KQ0 Roper Washer - Instructions

All installation instructions for RAX7244KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAX7244KQ0
16-30 of 1921
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer tub slammed into washer body during spin cycle

  • Customer: Brian from Seattle WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 103 of 115 people found this instruction helpful
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.

First I disconnected the washer from the water and power supply, then I laid it on its back.

The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.

Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.

The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.

With $25 in parts and about 15 minutes, my washer spins much more quietly.

The lid switch broke

  • Customer: Paul from Glendale CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 97 of 134 people found this instruction helpful
Removal Steps

1.Unplug washer and pull away from wall 6 inches or so. (You will need space on either side to remove the cover.)
2.Release control panel: Unfasten two screws at corners of panel. Tilt backwards. Unfasten old lid switch wire coupling and push it downward.
3.Remove washer cover (top and sides): Remove clips at two corners under control panel. You should be able to gently lift and remove the cover.
4.Remove lid switch assembly: Unfasten two screws holding switch to washer top. Unfasten ground wire (using 8mm wrench). Use screwdriver to lift up two clips holding switch assembly.

Reassembly is reverse of removal. When replacing the cover, line it up so that the side edges of the cover sit on top of the rail and the front edge slides beneath the rail. I learned this the hard way, and, in fact, it is still not fastened securely.

Cold Water would not shut-off

  • Customer: Wendy from Dunlap CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 67 of 73 people found this instruction helpful
To discover what the problem was, I intially tested the inlet valve by blowing into both sides - discovering that the cold side was stuck in the open position. The hardest part was removing the back of the machine. First, you unscrew the top plastic part which contains the controllers by phillips head on either side. Then you pop the clips out with a large slot screwdriver, then at the bottom, a nutdriver or large slot screwdriver there are two nuts to remove. The valve itself took a small nutdriver and pliers to remove the hose. Took less than 20 mintues to complete repair. Washing works like new now.

Water leaking on floor

  • Customer: Stanley from Warwick RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 66 of 71 people found this instruction helpful
I removed the two spring clips that hold the pump and two wire spring clips that hold the hoses. Then I had to pry the pump off the shaft (it was frozen with rust). Then I cleaned the shaft with sandpaper and installed the new pump (which, by the way, came the next day, thank you very much) which made my wife very happy, and I thank you for that , too.

Would not spin unless helped

  • Customer: Ernest from Oakdale CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 62 of 68 people found this instruction helpful
Turned off water supply, disconnected hoses so I could lay on its back.( drain hose also ) have something to catch all the water in. There will be some residual water so have something to wipe it up. Removed agitater, then I removed the spanner nut with hammer and punch. layed it on its back, removed the three mounting bolts that hold the gearcase to the tub support. Removed wire harness and ground wire , pulled gearcase and shaft out . Removed spin tube thrust washer, removed support ring from groove in shaft , removed retaining ring , slid clutch off shaft ,installed new clutch. Take care to watch how parts are removed so that they are installed in proper orientation. Since I had it this far apart I decided I should replace the coupling. I removed the two motor retainers , seperated coupling , pulled both halves off shafts , installed new halves , they go on a lttle tight , newer couplings have metal inserts , aligned coupling halves , inserted together , put motor retainers back on , tightened small screws,done.

washing machine not agitating

  • Customer: clark from paris TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 60 of 62 people found this instruction helpful
wife complained about washing machine making bad noise and she said it was not spinning. So being the good husband that I am, after she yelled at me 8-10 times I stopped what I was doing and sure enough she was right , the washing machine wasn't working correctly. Started testing the agitator by spinning it back and forth. it would only catch on the dogs every once in a while. the washer is only 3 years old, thought maybe one of the kids toys or lint was interferring with the dogs, pulled this dispenser off the top and then another plastic cap with a black o-ring off and found the agitator and dogs gears worn down and chipped. think it was a 3/8" socket I used, but you need a long extension to get to it. Part was labelled well and it was very easy to order. problem I had was when the new parts came in I had ordered the agitator repair kit ($16) and the thrust spacer ($5). Well it's not that $5 is alot of money but the spacer I had was worn and I was in there anyway so why not. The agitator repair kit comes with a thrust spacer but it was not shown on the otherwise very detailed pictures. So it would cost more for me to pay the shipping to return the unused part than not. the agitator repair kit description reads "This nine piece agitator repair kit comes with a two and a half inch cam, a thrust spacer, and four dogs (agitator dogs) but the thrust spacer is not shown. You could say I was 30% more into parts cost and make it sound worse. Had I been an actual repair man instead of a home do it yourself kind of person, probably would have known to call and speak with a rep vice going at it online solo. anyway, 5 minutes and the washer was back up, wife was happy, and I was able to continue with what i was originally doing.

Gearcase oil leak

  • Customer: Greg from Hemet CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 56 of 60 people found this instruction helpful
To replace gearcase seals, first disconnect the power cord. Turn off water supply and remove water inlet hoses at washer (safety first). You may want to have a bucket available to catch water that will drain out of the hot/cold and drain hoses. Next, remove top agitator cap, seal and (7/16”) bolt (see diagrams on PartSelect). This will allow the top agitator and cogs to be removed. Grab the bottom agitator and rock it back and forth until it can be removed.
Suggestion: now is a good time to remove and clean the old soap and junk from drain holes in the top agitator and any junk that may be under the lower agitator.
Lay the washer on its right side. You will now have access to the motor, pump, hoses clutch and gearcase. Place a couple of 2X4X(5?) blocks under the tub to support it. Remove the electrical connector from the motor (this is clipped into place) and the two wires that go to the capacitor on the motor.(TIP: don’t put your finger across these terminals, SHOCK HAZARD) Remove the hose clamps and hoses, the two screws (5/16”) on each strap that holds the motor in place, you may have to use a screw driver to pop the straps off the motor. Remove the motor and pump by pushing the tub to the left and move the motor and pump to the right to clear the coupling. If you have not replaced the drive coupling, now would be a good time to order and replace. With the motor out of the way, remove the three (½”) bolts holding the gearcase to the chassis and pull to remove gearcase and shaft. If you are only replacing the drive shaft seal, you do not need to open the gearcase case. Stand the gearcase so the input shaft is facing up, or what fluid is left in the gearcase will come out. One question I see a lot is how do you remove the seal. One, buy a real expensive tool that you will only use once, or take a screwdriver with about a ¼” blade, stick it between the shaft and the seal, gently leverage the seal out while going around the shaft. After the seal is removed, oil can be added thru the seal hole. Understand that different oils are designed for different applications. That said, I used 90 weight gear oil from the local auto parts store, you can add it thru the seal hole. To install the seal, lightly tape it into the seal cavity, then use a socket that is close to the diameter of the seal and gently drive it in.
If you have to replace the top case seal, it will require you to take the gearcase apart. The advantage of this is, if you have an older washer, you can clean out the contaminated oil and sludge and check for wear on the parts, and replace as needed from PartSelect. Here’s a suggestion: if you have a digital camera, take pictures, this will really help when you put things back together.
Now look at the diagram that is provide by PartSelect, remove the clutch, remove the bolts on the top cover, try to keep it level or you may have a mess on your hands. Lift the cover up over the shaft. I found the top case seal very stubborn to remove. Using a small screwdriver, get between the case and the seal and gently pry it out. Replace the seal, again, by using a socket and gently taping into place. There is also a seal at the top of the drive gear that you may want to replace to keep the oil from going up into the clutch. Now its time to clean all of the years of gunk out of the case and gears. When you are ready, fill the bottom half of the gearcase with oil, about half a quart. To seal the case, I used a ultra blue silicone gasket sealer in a tube from my local auto parts store or sealant can be purchased from PartSelect. I used it on the top half of the gearcase case. Slide the top case over the shaft and evenly tighten the bolts. Reinstall the clutch to the gearcase shaft and install into the washer. I found that the motor bearings needed to be lubed, so I used white lithium grease in an aerosol can. Reinstall motor and don’t forget to put the electrical plug back into the motor and the wires that go to the capacitor and pump h

Agitator had a terrible ratcheting sound when running in free-wheel mode during spin cycle.

  • Customer: Adam from Lehi UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 54 of 63 people found this instruction helpful
Removed the gearbox from the drum and removed the direct drive motor from the gearbox. Disassembled gearbox and drained gear oil. Rebuilt the neutral drive assembly with the ordered parts. Cleaned sealing surfaces. Filled gearbox with new gear oil. Sealed and re-installed the top cover to the gearbox. Reattached motor and then reinstalled assembly to drum and clutch (installed new clutch lining at this time as well).

Wouldn't agitate or spin.

  • Customer: Roger from Swainsboro GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 52 of 59 people found this instruction helpful
First, I removed two screws holding the bottom fiberboard panel in place, and the panel, to gain access to the motor, transmission, and pump. Unfortunately, I had the machine tilted to the front, and didn't have room to release the pump. I had to set the machine back up, and get manuvered around so I could lay it on it's back (I was working in the confines of a small laundry room). Once on it's back, I released the two clips holding the pump with a flat head screwdriver, lifted it up and out of the way without having to disconnect any of the piping, then I released the two clips holding the motor, again with a flathead screwdriver, disconnected the wiring plugs, and capacitor wires, then lifted the motor up and out of the machine. I then removed the two bolts holding the motor mounting plate to the transmission. Then, again using a large flat head screwdriver, I pried the transmission coupling half off the transmission shaft, I had to work it up, while turning the shaft, and then the same for the motor half. I then wiped off both shafts, and gently tapped both coupling halves back onto the shafts,
( this is easier using a socket that is just large enough to go over the shafts). Then I reinstalled the motor mounting plate, slipped the rubber coupling onto the transmission coupling half, lifted the motor into place, and rotated from the pump end to line up with the remaining holes on the rubber coupling. I then reinstalled the clips used to hold the motor in place, reinstallation only took thumb pressure to snap back into place, then, I reinstalled the pump, using the same method, and reconnected the wiring plugs and copacitor leads. Lastly, I reinstalled the fiberboard panel into the bottom, and set the machine upright, slid back into place, and reconnected the hoses and electrical, and tested the machine. Worked perfectly.
In actually took longer to disconnect the machine, and get it out and back in, than it did to replace the coupling.

Washer had water leak in lower front and would not drain.

  • Customer: Lowell from Dover DE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 57 of 74 people found this instruction helpful
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.

Machine rocking about like crazy on spin

  • Customer: john from middle river MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 44 of 48 people found this instruction helpful
Took some online research to figure out how to get the cabinet off. Once inside I fitted the wear pads which were a breeze to remove using a knife blade to pry them up and removing them using the screwdriver. The springs were replaced one by one using strong fingers. The machine went through the spin cycle without any rocking or self-destruct noises.

Tub wouldn't turn, but motor would allow it to drain.

  • Customer: Troy from Storm Lake IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 46 of 57 people found this instruction helpful
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tipped the washer on its back. I had to remove two clips to take the water pump off of the motor, then removed the two screws and clips which held in the motor. After removing the motor, I found the coupler was bad. To remove the gearcase, I took out the softener dispenser and removed one bolt to take out the agitator. Under the agitator was a clip. Three bolts held the gearcase to the frame. After removing them, the gearcase pulled straight out the bottom. Replacement was just a reverse process, with the addition of a light coat of grease to the gearcase shaft.

Washer would not complete cycles; typically would wash only but not drain and spin

  • Customer: Gerald from Chicago IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 42 of 48 people found this instruction helpful
Removed upper back and timer knob and then timer and wire jacket.
After replacing timer, washer at first did not work, then completed one load of wash, then on second load, it stopped at end of wash cycle, except when I leaned on lid which evidently closed the spin cycle switch which appears to be loose.
So I'm saving the old timer which may be OK.

The washer would not stop filling.

  • Customer: Clay from Laramie WY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 40 of 42 people found this instruction helpful
I took everything apart and put in the new inlet valve. Tried to run the washer and it was still not stopping when filling. I looked more into it and the tube that comes up from the wash basin to the load size selector switch was disconnected and that was the real problem. If this happens to you, I suggest first looking under the control panel at the clear tube and ensuring that it is connected to the switch. Then if that is connected it is probably the inlet valve. There are helpful installation videos that can be found on the part select website that I would recommend looking at before taking things apart because it will make it much easier.

Washer wouldn't drain

  • Customer: Karen from Columbus OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 40 of 43 people found this instruction helpful
I removed the screws & bolts to the control panel. Lifted the panel up & unhooked the wiring, then moved the control back & out of the way. Next I removed the clips that hold the back of the washing machine in place. I lifted up the top of the washing machine & was able to remove the damaged lid switch. Replaced the lid switch, which was relatively easy to do. Then I put the washing machine back together.
The key is to remember what & where the parts go: for example the clips that hold the back of the machine in place. You know where they go but not exactly how they go in & how the rear of the machine connects to it. But otherwise not a hard repair.
All Instructions for the RAX7244KQ0
16-30 of 1921