RAK2751KQ0 Roper Washer - Instructions

Turned washer on back, inspected pump area for leak and found crack in pump. Replaced cracked pump with new pump from PartSelect, which arrived promptly. Washer was only down for 3 days and turnup only cost me the price of the part.

Saw your video on how to install a waterpump. It made my life very easy.

Wacthed repair video online found problem ordered part 3days later part came installed worked like a charm smootest repair ever thanks john I told a neighbor about your service

Forget the instruction book, it's too time consuming and it's a knuckle buster. Disconnect all hoses and lay machine on it's back. (Have plenty of rags to soak up the half gallon of water still in the pump). Use pliers to slide back hose clamps on pump and slide off hoses. Use screw drive to snap off clamps holding pump in place. Remove pump. Simply reverse process to install new pump. It nearly was one of my wife's 5 minute jobs she always has on her "Honey Doo" list.

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

Replaced suspension, leveling and tub springs.

The washer breaks down slightly different than shown in the video. Install of the new part went pretty well. It was reinstalling the washer cover that caused most of the grief. You have to have all of that sheet metal lined up just right or it won't go back together. All good now...very happy.

I followed the helpful video from PartSelect. Removal and Replacement of the Clutch Assembly was fairly easy. Just make sure you have enough towels to dry up any water that may come out after tipping the washing machine over. After Replacement the washing machine works like new. Thanks PartSelect.

Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL

Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.

removed 2 machine screws a top of back plate with nut-driver, removed two Phillips screws holding control panel on with screwdriver, lifted control panel out of the way to get to tension bands holding back on and removed with small pry-bar. Pry open the back enough to remove electrical connections from Water Inlet Valve. Remove machine screw with nut-driver that holds Water Inlet Valve and slide valve out. Use pliers to remove hose from Water Inlet Valve. Reverse process for install.

I used the online video provided by PartSelect. It provides a better method of instruction than I can document.

The repair video was very helpful and exactly right. The most difficult task was removing the old pump. It had apparently seeping between the motor shaft and the pump coupler for some time and had rusted the pump to the motor shaft. I had to aggressively grip the pump housing with the channel lock pliers and wrench it back and forth to break it loose. I took a file to remove the rust build up from the motor shaft before installing the new pump. Washer works fine.

Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!