RAK2751KQ0 Roper Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water leaking from pump
Watched the video, it was so easy, if I had been a little younger it would have been a 15 min job...
Parts Used:
-
Anita from Globe, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Extremely wild rocking in spin cycle
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!
Parts Used:
-
Bryan from Midland, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Water not draining.
Started to replace the water pump but looked online at Youtube and everyone said to look at the lid switch first. I bypassed the switch and sure enough that was it! No need for the pump.
Parts Used:
-
James from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not always spin & was leaking water
Tilted the washer on the side with my wife holding it. Pulled the pump out then replaced it with the new one.
Parts Used:
-
John from Bakersfield, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Cold water was slow to fill and making whining noise
I followed the instructions on the video. One difference with the Kenmore model is that the screws were in front instead of the rear of the machine. Still had to pull the machine out to get to the rear to replace the valve. All went smoothly and the unit works like new. Now it takes less then half the time to do laundry. Great parts and timely delivery. Excellent instructional video and instructions. You folks are the best. Thank you.
Parts Used:
-
Edwin from Myrtle Beach, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water running from under washer
I found the impeller, in the water pump, had worn thru the front pump housing. Allowing water to leak on to floor. Replaced pump from under washer. Removed two hose's and two retaining brackets. Aligned pump and refastened hose's and retaining clamps. Works great. Thanks to Parts Select for the right part and the right price. Also Fast shipping. Dan H. Poplar Grove Il.
Parts Used:
-
Daniel from Poplar Grove, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Machine would not spin when pumping out water
You have to determine if it is the COUPLING or the TRANSMISSION or the CLUTCH. I checked the coupling and that wasn't it. The machine did rotate back and forth in the wash cycle so I thought it would be either the clutch or the timer assembly. I ordered the clutch and used the video to guide me through the installation. One problem was the PUMP was stuck on the shaft so I removed the hosed and took out the rest as one unit. The clutch was full of crud and after replacing it and checking for leaks, the machine runs perfectly now! I would suggest you replace the hose washers when you reattach them to the machine as I rechecked after turning on the water and found a TINY drip that would have been a problem over time!
Parts Used:
-
Charles from Novato, CA, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!