RAK2751KQ0 Roper Washer - Instructions

Removing the led and disconnected the wires and the unscrewed the valve assembly and removed it and reversed the steps putting it back together.

Followed the video instructions supplied with the email from Partselect, the video was very helpful and made the repair simple and fast

pulled washer away from wall unplug elec cord turn water off removed hoses pulled back of washer apart unpluged con on old valve removed small hose unbolted old valve installed new valve and hoses put all together tested with washing a load works perfect now only took 30 min to do repair very nice .

watched video and followed instructions, no problems.

disconnected power cord. disconnected water lines, pulled outer drain hose out of home drain standpipe. tilted unit forward. removed outer drain hose. removed mounting screw for drain pipe with nut driver. removed inner drain hose (defective part) with pliers. installrd new part in reverse order. new part fit like a glove.

had to take the entire shell off the washer and then it was 2 simple clamps.

disconnected the power, the water supply hoses and took the drain hose out of the wall. Tilted the washer back, undid the 2 clip,took the pliers slid the clamps back. Installed new pump. Put everything back. Done.

Our washing machine "squealed" as it filled. Only the hot water did it, the cold water did not. The hot water came in real slowly, and the machine made a squealing noice and the hose going into the fill valve would vibrate. When I ordered the part, on my order confirmation email there was a link to a video showing how to replace the fill valve. It literally took my less than 30 minutes to replace the part. The only thing that was different on my machine was the screws holding the controls on. Mine were hidden under a plastic cover on the front that I had to snap off. Other than that slight difference in screw location, everything in the video matched up perfect with my machine. With the new fill valve the machine fills in 1/2 the time. We hadn't really noticed how slow it was filling until the squealing noise started. After changing the valve, the difference in fill rate was very apparent. I'm sure the 15 year old valve was full of sediment and minerals. Works like new now.

The spin cycle was super slow leaving clothes soaking wet at the end of a full wash cycle. Ordered a clutch repair kit, watched the how to video that was e-mailed to me with my order while I did the repair and got it done in about 45 minutes. This was my first true appliance repair outside of maybe a busted fuse or replacing the heating element in a stove. Never thought taking the motor, transmission and clutch out of the washer and putting all back together would be so very simple. Meanwhile my wife is pissed because she thought she might be able to go get a brand spankin new washer...until I fixed the old one. Thanks for saving me some dough PartSelect.

used pliers to remove rings on 2 hoses, popped 2 retaining clips off of old pump, put new one on, hooked up hoses, fastened clips and was done!

My son and I leaned the washer backward and I had my son hold it while I got underneath of it and unscrewed the two hose clamps to loosen the hoses, pulled them off. Then I flipped the two clamps holding the pump in place and the pump came right off and it took about 2 minutes. I ran into a little problem putting the new pump on because I wasn't getting the drive shaft lined up quite right, otherwise the whole thing would have only taken about 10 minutes total. As it was I got the pump mounted, repositioned the clamps and then hooked up the hoses...done! The design is perfect for ease of pump replacement; kudos to the engineers who designed it!

move machine away from wall---shut off water and remove hoses--loosen screws that hold valve on back wall---remove toplid, place to side--diconnect water line at tub----disconnect wires to valve,hot/cold---remove old valve with hose attached---take new valve and place new mount bracket on, little tricky did not line up at first must force plate to slid into plastic slot so screw hold lines up, without breaking new valve---once bracket on replaced all---used tape on inlet valves thread when supply hoses replaced--seems shorter than old valve--but tighten up OK no leaks

My washer leaked water in after wash cycle and cloths were wet after spin cycle. The cause of problem was defined in Parts Select trouble shooting guide. Replacement was just as the video described, except this model had two screws on front of control panel and the panel tipped back on hinges. Look at both sides of washers, so when you reinstall the body you know how it should look against the back panel. I didn't slide the whole washer body off, just tilted against a wall. Also, it's not necessary to get behind the washer, so the repair can be done in a tight laundry rooms like mine.

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

very easy I followed the Parts Select video that's posted at the site,and covered the replacement very good.Thank You very much.