PHS69EHSS3 Frigidaire Refrigerator - Instructions

first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Purchased a new ice maker assembly and installed. Very easy

Easy to install (self explanitory)

before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Easily removed door and installed new parts. Perfect fit.

New bins slide and snap into position with no tools required. EASY!

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Removed shelve from frig. Removed old rails from the shelve and installed the new ones. Reinstalled the shelve into the frig. and installed the drawer. Less than 5min.

Open box, peal plastic off of glass, slide glass onto shelf brackets

First of all--outstanding delivery time. I chose the cheapest 3 to 5 day delivery and the parts arrived the very next day. The closer plate was a breeze. The hinge bearing was challenging becaue it was broken off flush to the bottom of the door so it took some time with a needle nose plyers to break it into small pieces to remove it from inside the door. Once that was done it was easy replacing the hinge bearing, reassembling the door. Like others have mentioned it took the longest time taking everything off the refrigerator door. Just glad PartsSelect suggested ordering both parts at the same time since I had to replace both of them.