Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blanket jambed drum, belt kept turning burned belt and pump
Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.
Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.
Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.
remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.
Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.
Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
broken fin on agitator causing unbalanced wash/spin cycles
popped off fabric softener dispenser, 1/2" socket on 8" extension to remove 1 bolt. Lift agitator to remove and clean area under agitator in tub. Lower new agitator onto spindle (pretty much aligned itself) and re-inserted bolt to secure in place. Replaced softener dispenser...done. REALLY easy....
Parts where in, in a timely manner. I remover the fabric softener cup on top of agitator. User a 1/2 inch socket and a 3/8 ratchet with an 8 inch extension to remove the center nut. Popped the agitator out. Installed in reverse order, only tightening the nut slightly. The install went just like the video. Thanks much.
remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor