MZD2766GEB Maytag Refrigerator - Instructions

I ordered the ice dispenser and selenoid door kit, it was easy to repair because I only needed the door. As per the instructions I removed about seven screws and disconnected the power source to the dispenser unit, pulled the unit out
and replaced the door in the two slots. Plugged the power source back into the slot, put the screws back in, now it works like new.
Thank you PartSelect, I received the part in just a couple of days. I recommend your service to everyone. I saved myself a lot of money and will order again on any needed
parts in the future.

I followed the instructions supplied by others on your site .They were right on. The repair was simple with the instructions. The service was absolutely superb. I ordered the part one morning.
The next morning Fed EX delivered the part to my door. I will use your site for parts from now on.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

First i unplugged the appliance!!! Then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. installed fan.
Removed inside panels from back of freezer and de-frosted coils with hair dryer (20mins).
CAUTION! "Mop up and dry area of exsess water before pluging appliance back in!
Re- assemble panels and plug in.

removed outside water spill tray and removed exterior cover & interior cover exposing the door arm and solenoid. replaced with new parts including spring. Elontronics have a plug which is easy to disconnecct. & reconnect
old solenoid head would not have fit new door arm
and vice versa.
I strongly suggest using the kit.
A Torx type screw driver is required for all screws
on the Jenn-Air

I removed the one nut screw holding the Ice bucket shelf then removed the Ice Auger Container. Then I lifed the Part containing the Drive Motor. I removed the electrical connection which just plugs into the fridge. Once the Drive motor and container was out of the fridge I removed 4 screws and the Drive motor was out. I disconnected 3 electrical connectors and connected them to the new drive motor. Then replaced the motor and connected the 4 screws. I then installed the yolk on the drive shaft and then put the drive motor container back in the fridge and reconnected the electrical. Installed the nut screw and I was done.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had short wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.

The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!

unpluged frig, removed rear cover removed 120v supply connector, removed three fan support screws.Changed fan blades to new motor unit installed fan support screws,installed 120v connector plug frig in, test fan installed rear cover .....

The actuator rubber pad had hardened over time so that it wouldn't allow the solenoid to retract and stop the flow. To fix: Turn off fuse to fridge. Removed the screws on fountain faceplate. Remove faceplate. Unscrew fountain computer assembly (2 or 3 screws) to access the actuator pad from behind. Unplugged the computer ribbon. Replace black actuator pad.

It works fine now.

First removed the old water filter and replaced it with the filter bypass. Very simple and no tools needed

I reasoned that the water-value was caked with hard water deposits, or perhaps just worn out. I traced the plastic water line to the back of unit, then found the double water valve. I was not "sure" that this was the problem, but I order the part any way and it fixed it!! The removal /installation was pretty easy. First turn off the water supply to the unit. Then loosen and remove the incoming copper pipe from the unit. Remove just two 1/4 in. hex head screws and carefully pull the unit out a bit. Then remove the electrical connectors and the plastic tubing connectors. Just do the reverse to install it. I am very happy with the item ordered from PartsSelect. Perfect. And shipping time was fast too. Thanks guys.

First I removed the top hinge cover plate. Then removed the three screws in the top hinge. I lifted the door off the lower hinge and laid the door on the kitchen counter. I removed the one screw holding the natural door closer part from the bottom of the door and installed the new part with the same screw. I then replaced the lower hinge pin with the new one. It just sets in place. I then repositioned the door and reinstalled the top hinge. the whole job took about 15 minutes after the refrig door had been emptied. The door works like new.