MZD2766GEB Maytag Refrigerator - Instructions

unplug refridgertor shut water off. took off water line at valve un plug wires unsrew mounting valve. srew water line back plug wires back and mount vavle. turn on water. plug refridgertor in

First I rolled the fridge out and unplugged the power cord. I then removed the ice bin. There was one screw to the left under the ice bin rack holding it in. After removing that screw, I could pull the rack out far enough to disconnect the electrical connector. You have to squeeze the wings b-4 you can pull the connector loose. I put the rack on the countertop, removed two screws and the solenoid with plunger came out. I replaced the old solenoid, put everything back together, and realized I probably just saved myself $300. My Wife thinks I'm a Hero again. It works fine now.

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

Unscrewed old filter and screwed in new filter.

1/4 turn of old filter. it popped out. Inserted new filter, 1/4 turn and it clicked in. Piece of cake. I'm a freakin' genius.

the main water valve was leaking causing the water under the frig. But the double out let valve was not holding causing a ice build up in the ice bin. The repair was not complicate you take back cover off turn off water. use the nut driver to unbolt the valves from the frig with frig unplugged use screw driver to remove the power plugs from valve. use flare nut wrenches to remove main water line.push on plastic retainer rings to remove plastic tubing. remove valves from bracket and then reinstall in reverse order.

googled for answer, deduced relay/switch problem. googled again for parts, found partselect.com, ordered part. 2 days later & $70 lighter, my 8yr old Maytag was working again! Parts were good fit, instructions were decent enough. Not for inexperienced tinkerer though.

took off door and replaced parts and replaced door

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

The valve on the frig cracked when the frig was in freezing temps during a move.
The part was slightly different than the picture on the parts website due to a design change that eliminated the Y in the water line created only one connection on the valve where there used to be two. I found this out reading on other websites.
This design change also resulted in a part number change, but because this website had such good pics and views, I was able to determine the part was right. We received the part within 3 days and installation was easy. We eliminated the Y in the line and attached the fittings.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

First I unpluged the frigerator, then I turned off the water. Then I removed the the black cover from the bottom back of the frig. The valves are located on the bottom right. Unscrew the bracket that is holding the two valves. I then removed the bottom valve from the bracket, unplug the electrical connections, and connect to the new valve.
To remove the water lines from the valves just move the white ring around on top of the valve and pull the line out and insert into the new one when ready. (the valves are the same colors) Do the same to the top valve, mount back to the bracket, then mount the bracket to the frig, hook up your water line to the valve, turn on the water and check for leaks, plug it in. Then put a glass under the water dispenser and try it out, it'll take a few seconds to get the water running through.
PartSelect was very quick on getting me my parts, TWO days, couldn't believe it. Very good examples of parts on web page.
Very satisfied and will use again.

Removed top hinge cover. With nut driver, removed the three screws that held top hinge. Gently lifted door off bottom hinge and laid door across sawhorses. Once I saw what parts were worn on bottom hinge, removed them. Was a little confused from parts diagram online to what I had in my hand and needed to put back on door. After a few minutes realized I had ordered basically a duplicate part, "closer with cup", didn't need it. With a screw driver easily replaced new parts and reassembled the door. Works great.

I removed the black drip grill and unscrewed the two screws holding the faceplate in place. After unplugging the faceplate from the dispensing unit, I removed the four remaining screws; be careful, one screw is shorter than the others.

I then pulled the dispensing unit away from the freezer door and removed the ice door assembly. WARNING: Make sure that you look carefully at the alignment of the return spring BEFORE you even touch it because as soon as I started using the needle-nose pliers to remove the spring, it shot across the room! Also, look carefully at how the end of the plastic rod fits over the old solenoid; in fact, look carefully at the entire plastic rod and how it aligns with everything!

Unfortunately, the pictures in the instructions are fuzzy so you can't really see how the spring is installed and how the plastic rod fits over the solenoid.

The solenoid was easy to remove and replace. Be aware that the plunger part of the solenoid slides in and out easily, so it's easy for it to fall out of the solenoid unit and roll away.

Once I had everything back where it was supposed to be, I screwed everything back in and the ice/water dispenser worked like new. I was even able to clean off some calcium deposits inside the unit while I had it opened.

If I have to do this again, I would estimate that it would only take 15-minutes or so. It took me longer because I didn't look at the alignment of the plastic rod in relation to all of the parts---that is one of the most important steps of this operation.

Anyone who is comfortable using tools and working with small parts should be able to complete this replacement project with minimal difficulty.

Removed the drip tray and cover panel. Then removed shoot housing, replaced broken door and reassembled in reverse order. Easy as pie.