MTAP1000M0WW Hotpoint Washer - Instructions

Replace

just like the video showed/////only idid not kno the water would escape from one of the hoses when removed///video did not prepare me for this

My washer was full of water after it wouldn't drain as part of the wash cycle. I used a Wet/Dry vacuum to remove the water from the tub. Followed the video provided on this part page. When I pulled the hose from the wash tub to the pump at least a gallon of water that I was in the bottom of the tub and hose rushed into the base of the washer. It was an unexpected mess to clean up a the end of the job. Pump was fairly easy to remove from the washer, but reinstalling the hoses to the pump was slightly more challenging. The hose from the tub to the pump is about an inch too short to make this an easy fit. I had to have my wife hold the hose clamp open with the channel locks while I positioned pump onto the hose. After the hose was installed, the second hose was much easier to install. With the new pump the washer running like a champ!

remove screws from bottom of washer to remove the bottom of the washer so you can access the pump and motor assy. and remove two hose clamps.

Just traded out the hoses and installed washer and started washing. Also got the replacement hose in a very timely manner, in turn only without washer for 5 days total. Thank You

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

Took 30 seconds after I recieved the part from you guys. $8 repair. Sweet!

This job did not take much longer than 15 minutes if that.1st take the cord or twine and loop it under 2 paddles of the agitator.( there is a small groove under each of the paddles that has enough space to put the cord in) Pull up on the cord to remove the agitator. 2nd. Under the agitator is a bolt that secures the agitator coupling. Remove that bolt. Keep bolt(you may want to replace this bolt if rusted and worn. Mine was still ok so I reused it.) 3rd pull up on Agitator coupling to remove. Teeth were worn on Coupling, So discard. 4th Insert new coupling, replace bolt to secure coupling. finally slide agitator back over coupling till locks back in place. ....Done.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

After the GE Washer went dead last week Tuesday while my spouse was doing laundry, I I took it to the back yard just to examine the inside from beneath before going to find a new one that evening.
While on its back I notice that the motor still worked but it was very weak. Taking the belt off it went a little faster but weak. Then I remembered that there was supposed to be an electrical part that sends or allows current to go to the motor, but didn't know the name nor what it should look like.
I started my search and found this cylindrical electric part that had a scar on the outside and a hardened mass protruding from the inside. Since the wires to and from the part was the same color, I marked one terminal, then took pictures of the position and wiring of the part I identified as the problem, then took it out of the machine.
At this point, I went to the car, sat inside, started the car, and was about to leave to find a washing machine, then I thought of the Internet. I went on the Internet, found a store that sells GE washing machines parts, identified the part to be the capacitor. I ordered the part late that evening, received it Thursday afternoon, installed and reassembled the machine immediately, and today is the eight day since the fix and as I am writing, Thursday, August 15, 2013, the machine is doing my laundry. The diagrams made it very easy to identify the name of the part, and since I am mechanically inclined, getting the old part out and installing the new part was very easy. ~~ Vasco

With the instructions found online, this was a quick easy repair. I used youtube to have video to show the method. Used rope to pull up agitator, used wrench to loosen bolt and then put back together. Part was delivered really fast, I recommend Partselect.com for the parts you need!