Models > MTAP1000M0WW

MTAP1000M0WW General Electric Washer - Overview

Get Parts and Repair Help for MTAP1000M0WW

If you know the washer repair part you need, you can browse the list of all parts on the MTAP1000M0WW, or you can search by name or part description. You can also find your part by where it is located on the MTAP1000M0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for MTAP1000M0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.71

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$9.75

Drain Hose Extension - 4 1/2' Long

$3.27

Timer Knob Clip

$5.54

V-Style Drive Belt

$3.00

Drain Hose Clip

This clip holds the drain hose to the back of the washer.

$7.23

Tub Seal

The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.

$53.39

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$3.00

Tub Bearing

$6.62

Agitator Coupling

Bolt not included. This part connects the transmission drive shaft to the agitator base.

$7.45

Hub Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 154 of 164 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

GE washer no spinning during spin cycle

  • Customer: Laurence from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 80 of 89 people found this instruction helpful
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Lo... read more

The Hub Under the Spinner basket broken/ Deteriorated

  • Customer: Joe from Lucedale MS
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 50 of 66 people found this instruction helpful
Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chisel and bust Old Alum... read more