Models > MMW5530DAB > Instructions

MMW5530DAB Maytag Oven - Instructions

All installation instructions for MMW5530DAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MMW5530DAB
46-60 of 110
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not heat

  • Customer: Ralph from Nicholasville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

handle broke on one side

  • Customer: Howard from Ticonderoga NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.

Broken oven door hinge

  • Customer: Stephen from Monmouth OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

The Old Hinges broke off and the door would not stay closed

  • Customer: Bruno from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

Dried out seal

  • Customer: Clark from Abbeville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
The repair did not happen as the seal was much larger (fat) than pictured. The one inch graph paper indicated the seal was 1/2 inch wide, which was the exact measurement of existing seal, but when it came it was closer to a full inch wide (fat)? This was my last hope as no one else has the right one either!

After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot

  • Customer: Philip from Winter Haven FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Oven Over Heating

  • Customer: Steve from New Albany OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Oven temperature lagging set temperature by almost 100F

  • Customer: William from Edgewood WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

After cleaning, F1-1 error flashed and neither oven worked

  • Customer: Georgene from Rock City IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Oven not heating to desired temp

  • Customer: Raymond from Ridgecrest CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Varying heat

  • Customer: Kimbel from Rhoadesville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

not heating/kicking oven off

  • Customer: Kevin from Virginia IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Broken hinge

  • Customer: Don from Exchange WV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 2 people found this instruction helpful
Took the door apart and replaced the hinge, very easy

Getting codes and beeping

  • Customer: Arthur from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.
All Instructions for the MMW5530DAB
46-60 of 110