MFI2568AEB Maytag Refrigerator - Instructions

The repair was very easy . . There was no tools required. The shelf rail just snapped in and out very easy

I replaced the broken part. There was one bolt to loosen with a nut driver. I disconnected the original wiring harness, reattached the new harness and reinstalled the hinges, which simply slide into place. Then I reinstalled the small bolt I had removed with the nut driver. The job was with no problems.

broke pins wed. morning ordered end caps wed. afternoon parts arrived next morning at 9:30 had it fixed by 11:30 30min repair time and i'mm 77years old. Out standing service. Removed veg. trays removed glass above deli tray removed broken pantry end caps installed new end caps two screws each.Very easy,took less than 30 min. Thanks

1.remove upper cold storage bins 2.rremove top glass on lower storage meat/cheese bin. 3.remove trim parts from front and rear 4. remove bin 5. remove trim pieces and slider mechanism from right side and back. 6. replace with new parts. 7. clean out gunk which accumulated on bottom of fridge. 8. reassemble in reverse order 9. Took longer than anticipated...over one hour.

Was a very tight fitting part and it had to be gently tapped into place.

Removed both veggie crisper and lower center crisper, removed glass shelves, removed broken side pantry end cap two screw, two were missing. Hardest part was to remove the rear adjustable piece and install on new end cap. Glad I took my time as the center rail will probably have to be replaced again. Poor design, numerous other comments say the same thing. Best part of the repair was ordering from partselect. Co, shipped on time and ordering was easy with complete parts diagrams.

Removed the drawers and glass. Removed two screws holding the end cap in place. Reversed process for new piece. Really really simple. Don't pay somebody else to do this.

biggest time was the cleaning of the area ;-) for the actual work it was less than 10 mins to replace. remove the three screws and there are two tabs on the back of the replacement part that you need to line up with the slots in the back and it simply snaps in place - put the screws back and you're done

I followed instructions provided by others on this page. I can't believe how easy it was.

Removed lower drawer and two drawers above the section to get to the left side guide. Removed screws on old guide and installed new guide. Placed drawers and new cover back into the refrigerator. Done!

Found "pegs" either side of drawer found "holes on side of lid pushed holes on side of lid onto pegs.

Removed all plastic drawers and glass shelf. removed two screws holding the part to the side. Removed the slider metal part and placed it on the new part. Reversed the process, project complete.

The Deli Drawer needs to be re-engineered as it is constantly getting stuck when closing which caused pin to break. Fix: removed deli drawer and contents, removed 2 screws holding right-side metal slider and two more screws holding Pantry end cap. Surprise was that the Pantry End Cap had a long, movable plastic arm attached (used to adjust amount of cold air delivered to deli drawer). This long arm has to be carefully removed (unbelievable) from the pantry end cap in order to replace on new end cap. Luckily nothing broke. Count on 30-40 minutes. Sad that such a high-end refrig couldn't have a better design.

I cleared the bottom drawers and lifted out the glass and set aside. Removed both drawers. Removing right side panel (end cap) was just 2 screws for hinge and 2 screws for end cap. Note that there is a small tab toward front of end cap that needs to be gently popped out. Taking the temperature control lever and slide assemblies were easy once I figured out how they snapped out and back into place. No tools required but takes a little looking and thinking to swap them out. Try moving lever at an angle to facilitate replacement. Swap hinge and then position new end cap in place and screw in place with the two screws. Add drawers and glass back in. Ouila!

I unscrewed three screws and took off broken side. Then I unscrewed three screws and removed and replaced drawer slider. I then replaced old side with the new one.Thanks you for making this so easy.