MFI2067AES Maytag Refrigerator - Instructions

i first removed the ice maker and took the motor assembley off. Right away i saw the problem. The wheel which drives the arm broke.
Once i get the new motor modl i just replaced it (it just pops into place with 1 or 2 screws).
put ice maker back in freezer and wola. Starting cranking out ice within 15 minutes.

The minute my parts arrived, I took the drawer out, unscrewed three screws, replaced the side with the latch and then snapped the lid in place. It took 15 minutes and my fridge looks brand new.

Thanks so much for your speedy delivery. It was a great experience and I fixed it myself .

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

Replace with. New part. Website made selecting the correct simple. Easy to order. Prompt delivery. Quite easy to replace broken part with new part. Now the door shuts automatically again and seals very tight. Successful experience!

Old grille had fallen off, so we just had to snap the new one on. No tools required. It is so perfect a replacement, I didn't even notice that my husband had installed it.

installed new parts

I ordered ENDCAP WPL 12656020 which arrived only days after I ordered it It was easy to remove broken endcap - the tab which held the lid had broker off as there were only 3 bolts which needed loosening (easy to accomplish with socket set). The mechanism which adjusted how cold drawer is needs to be carefully removed. If you fiddle around with it, it will become apparent how to take it apart. Putting drawer back together was straightforward, but be gentle with the parts as they are made out of rigid plastic.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

took back covers off until I found the electronic control box. looked up model # and searched the internet for repair parts. ordered on sunday afternoon around 4 pm. received the following tuesday around 9 am. (great delivery time). pryed the retaining clips to remove the circuit board and unplugged the 4 wiring harnesses. installed new circuit board and covers. plugged in ref. looked up the programming code for my ref. and used the accompaning directions to program the circuit board to my ref. it immediately started to cooling and working great.

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.

Let me first say that I ordered this late in the day and it was here by noon the following day. I wasn't too sure on how to remove the front, white panel from the damaged crisper pan. While on the website, others had explained that you had to remove the white panel from the front of the drawer and did not mention any tools needed so I just snapped it off on the one side and then the other. I'm so glad I finally replaced the entire drawer as there were times when I forgot it was broken and many pieces of fresh fruit ended up on the kitchen floor.]Service was outstanding and will now order my icemaker for replacement.

perfect part (too bad this and sooo many other appliances) are interchangeable) HEY! maybe thats why they all look alike. (WHIRLPOOL)

Terrific service company don't hesitate. Simply outstanding received it the next day! Wow install less then 10 minutes. No complaints.

I removed the ice maker, saw the problem, took the ice maker apart and ordered a new mold. I reassembled it with the new mold and it now makes ice but the control arm remains up after each ice dump. I plan to take the ice maker back out when we leave (we are snow birds in Florida) and see if the arm is properly placed.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.