MER6770AAW Range - Instructions

verified that the heating element was at fault by measuring it with ohmmeter. There are 3 contacts on the outside of the element. Resistance between center contact and either outside contact should read something close to 0 ohm, if it is good, and if it is burned, it will read open circuit (infinite resistance). Wanted to make sure that this is not the switch, which I replaced a few months ago. Before I disconnected all the connectors from the element I made picture of all the connections, just in case I forgot what gets connected to what (didn't use it, though). Installing the new element was very easy. Most work is done getting access to the element. Repair went smoothly, range works fine, now.

Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath towell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job

Turned off the breaker to the oven. Removed the two screws, disconnected the element from the wires in the oven. Reversed the process to install the new element. But the best part was that the replcement element arrived in less than 24 hours from when I ordered it. Amazing

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

Shut off power at breaker box. Removed the door of the oven. It just lifts straight up. Removed 2 screws where the coil enters the back wall of the oven. Slowly pull the coil out and the wires will come with the coil. There is enough wire to pull the coil out a good 6 inches. You can then pull the connectors off the old coil and attach them to the new. Fish the wires back into the holes they came out of then line up the screw holes in the coil and tighten them up. Slip the door back on and restore the power.

went to u tube and followed the instructions, took me less than an hour. Was super easy, and way cheaper than paying a repair guy $300.00.

turned off power to stove, removed two screws in rear of stove at element plate, removed two color coordinated terminals, hooked terminals up, installed two screws, and turned back on power.

It was really easy to replace the element. Remove two screws that holds in the element and pull it out about 3 inches. Remove the two wires and put in the new element. Plug in the 2 wires and screw it back in. It took about 10 minutes and the oven works great now!

Removed door from stove. Took off metal trim around door and removed glass. Took off top door trim and removed handle. When I put the glass back it was slightly wider than the trim piece and the end broke off the new piece.

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

unscrue 2 scroos remouved from the soccets and poot the new one

Extremely easy replacement. Followed the instructions and suggestions from previous users which was emphasized about turning off electricity. Main difficulty was that we are not young people, had to reach on knees and stretch to back of oven. Put hot pads under knees for comfort !!!!!!