Models > MDE9206AYW > Instructions

MDE9206AYW Maytag Dryer - Instructions

All Instructions for the MDE9206AYW
631 - 645 of 751
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Timer Knob
Simple old one cracked, popped new one on!
Parts Used:
Timer Dial Skirt Timer Knob Base
  • MARSHALL from ELLENWOOD, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
broken short baffle
My husband, who normally calls a repairman for everything, followed the video and replaced the short baffle in less than 30 minutes from start to finish(this includes 2 or three trips up and down stairs to retrieve the right tools even though the video tells you the right tools to use). The part was identical to the original one and arrived in less than a week. Am very pleased with the whole process and am so thankful for the step by step video. The full repair was less than $30.00 for the part and my husbands time. I had been given a quote over the phone for this same repair of $250.00 to $375.00. Thank you so much and I will definitely buy from here again if it becomes necessary.
Parts Used:
Short Baffle
  • Teresa from Acworth, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
rollers worn ,rumbling when drum turned
removed front cover and rear access panel took belt off tensioner removed front drum support removed drum replaced two rollers by removing snap rings and put it back together in reverse... The maytag repair man is still lonely
Parts Used:
Drum Support Roller Kit
  • scott from auburn, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Loud squeak coming from rollers
The online video was the extremely helpful in aiding me in the repair. Thank you so much for posting it. Couldn't have done it without it.
Parts Used:
Roller Shaft Drum Support Roller Kit
  • David from Chino, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
The timer skirt broke
Ordered new timer skirt. Watched video on replacing it. Removed timer dial skirt and knob. Used screwdriver to release tabs on knob. Made sure the metal insert on old skirt came off with the old skirt. Installed new timer dial skirt, pressed knob into place and made sure it latched. Installation complete in 30 seconds. Fit and works perfectly. Only problem I have had in 14 years other than the inside light burns out often. Thank you!
Parts Used:
Timer Dial Skirt
  • Everett from Clute, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
noisy and drum wobbling
Installing the Front Glide Kits was straight forward if you watch the video. The guides resolved a part of my problem, but I discovered the Blower Wheel was cracked and out of round. replaced it and poof its fixed!
Parts Used:
Front Glide Kit
  • Jeffery from West Linn, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken door catch: female half
noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!
Parts Used:
Door Catch Kit
  • Allen from Seattle, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
loud noise
watched the video, took the dryer apart, installed the new parts, reassembled the dryer, video was very helpful .
Parts Used:
Idler Arm and Shaft Idler Pulley Wheel and Bearing Roller Shaft Multi Rib Belt - 91-5/8 Inches Drum Support Roller Kit
  • Rachel from Tabernacle, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
New rollers replaced
Followed the guidance on video.
Parts Used:
Drum Roller Shaft Washer Drum Support Roller Kit Retaining Ring
  • David from Helena, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door catch broken.
I pried out the old one slightly and grabbed it with pliers. Quite possibly the metal catch dropped into the door section, but no problem. I pushed the new one into place with the side of the pliers. Probably 3 minutes time.
Parts Used:
Door Latch Kit
  • Byron from Los Angeles, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer started making nocking noise
found info describing the nocking noise found parts to fix it watched video on how to do the repair The step by step instructions made the job so easy We saved over 150.00 in doing the job ourselves. thank you I am amazed at how simple this turned ou to be.
Parts Used:
Front Glide Kit
  • Myra from Dillon, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Belt was squeaking
Sorry didnt unplug it. Just took door off. undid next panel and moved it to the side. Took bottom front panel couple of hex screws. Lifted basket out a little took belt off and replaced with new belt reversed order of panels and started it up.
Parts Used:
Multi Rib Belt - 91-5/8 Inches
  • Kent from Sealy, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
slow in drying, making a lot of noise
I followed the instructions
Parts Used:
Drum Support Roller Kit
  • Byron from West Harrison, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
knob for timer select was broken, the plastic around the metal part was cracked
very easy remove the old part, insert new one, works great
Parts Used:
Timer Dial Skirt
  • Robert from Huntley, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
timer knob was cracked allowing it to spin around the timer setting stem
Removed the old knob and skirt. Replaced them with the new parts. Works like new!
Parts Used:
Timer Dial Skirt Timer Knob Base
  • David from Lenoir, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MDE9206AYW
631 - 645 of 751
Back to Top