MDE21PNAGW Maytag Dryer - Instructions

after watching the repair video on your website I just followed the instructions. It was real easy.I re-attached one baffle, installed a new baffle and tightened the screws of the third baffle.

I did the repair has the video showed me.

I followed video, took out two screws from bottem front of dryer. removed door set a side, used a nut driver to remove the 4 nuts holding the front drum panel, I used a 1/8 drill to remove 4 pop-rivets holding what use to be front glides,I put the new glides in cork parts first then the plastic parts, than used my poprivet gun to but in the new rivets. I put it all back together and now no more holes in my underwear!!!

First I took the front of the dryer off and removed the drum (of course, after disconnecting the power supply) Removed the belt and then the roller itself. I had to open a removable port on the back side to reinstall the belt but that was also very easy. The videos made it all seem soooo simple. Thank you.

It was only "difficult" because it was the first time. The web site had good videos on how to open the dryer and access the parts. One user posted a very helpful suggestion. Although replacing the drum support rollers were highest on the suggestion list, the user suggested to also order the idler pulley wheel and bearing at the same time just in case that was the cause. I did that and sure enough, it was the idler pulley wheel that was squeaking.

I originally diagnosed as tension roller but found it to be a drum roller. Plastic had separated from the Babbitt bearing. So replaced both drum rollers and returned the tension roller. Only problem was the video was not for Maytag Neptune but a more generic dryer and I spent an extra hour try to reattach the drum belt. The video was the one that came with the email notification of part being shipped. Hook up to motor drive is backward from what the Neptune is. Eventually went looking for another video on my own and discovered the difference.

I viewed the roller replacement instruction video on the website which was very helpful since I had never replaced drum rollers. A leisurely pace of one hour to replace the two rollers, half of which was spent vacuuming the interior. Removed the front panel without tipping the dryer. Had to disconnect a ground wire to remove one bracket but otherwise only had to remove screws, slip rings and washers. No belt removal. Drum was pulled away from rollers but remained in cavity Reassembled without any problem. Ran the dryer - much quieter and no longer had the whirring noise.

Googled repair video on You Tube to assess ease of repair. Disassembled dryer front and top. Removed and replaced the above parts as well as earlier order of drum slides and drum rollers. Checked motor was working prior to reassembly. Reassembled and everything worked well once used a couple of times to allow things to stabilize.

Cleaned and greased rear drum support rollers.Fine emory cloth on roller shafts. Replaced front support glide strips. Replaced blower, retaining ring and clamp.

watched the u-tube video provided by you Part Select, very easy to follow, removed the thermostat and heating element as instructed, determined it was the thermostat and replaced it. The dryer works great. We saved alot of money thanks to Part Select.

first thing i did was look at the repair video 4 times. after that the replacement on of the guides were simple. thank you for suppling the video.

Removed old belt and installed new one by removing front panel and tub

After watching the video on this web-site it was very easy. I took the time while I had the drum out to vacuum out everything inside the cabinet and sprayed the sealing felts with silicone spray before re-assembling the unit. Wallah!! No 'mo' squeaks. Tommy

Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.

My husband, who normally calls a repairman for everything, followed the video and replaced the short baffle in less than 30 minutes from start to finish(this includes 2 or three trips up and down stairs to retrieve the right tools even though the video tells you the right tools to use). The part was identical to the original one and arrived in less than a week. Am very pleased with the whole process and am so thankful for the step by step video. The full repair was less than $30.00 for the part and my husbands time. I had been given a quote over the phone for this same repair of $250.00 to $375.00. Thank you so much and I will definitely buy from here again if it becomes necessary.