MDE17CSBGW0 Maytag Dryer - Instructions

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

First, I replaced the male end which was just two screws and simple replacement of pushing the fastener into the door frame. When finished I noticed the female end was damaged as well. Glad the female part came as well. This required taken off the front trim around the door (four screws - 2 each side) and then the door. The installing of the female end was easy with a little push. The damaged female end was already hanging out so easy to grab and remove. Otherwise I would have had to remove the front panel. Note You need to put the door trim back on before reattaching the door.

This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.

im a car mecanic it was easy

I took the old filter out and placed the new one in the same spot.

Had to unstack the unit took it apart and replace the rollers,Belt and Idler Pulley It was the pulley making the noise but I had it a part and for the cost I replace the rollers and the Belt the Job was easy The Washer and Dryer are Great we run about 2 Loads a Day

After removing the back & top of the dryer,I determined the noise was coming the idler pulley.I went online w/ model # & found Partselect.com.I ordered the dryer repair kit (at my door in 3 days) which included all the rollers,idler pulley, belt & hardware.It was an easy job to do even tho instructions were for top control panel model (mine is a whirlpool duet- front control) I did try using silicone lubricant on idler pulley, which worked to quiet dryer for a couple days so my wife could use it while I was waing for parts.Two thumbs up to Partselect.com,I will be purchasing all my appliance repair parts from them..I own all whirlpool stainless steel appliances that have been very reliable,but it's nice to know I have Partselect to fix problems as needed.

self...right part thank you

ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

I would like to say first of all that I was amaized and pleased at how simple the ordering of this part was and while looking at the parts diagram on you website I noticed the door swing was optional and could be easily changed and the dryer came from the factory with a latch installed on both sides of the door. In our laundry room the dryer sits to the left of the washer and the door to the dryer opened to the right which has always been a slight inconvenience. . . So instead of changing out the broken part, I took the door and hinge off with my cordless screwdriver (6-8 screws) and turned it around and remounted it on the opposite side. . . Simple! I never took the new part out of the ups envelope. Now I have a spare so I taped the new part in the envelope to the back of the dryer in case I ever need it and now we have more convenience with the door swinging the correct way. Sweet deal! Took less than an hour. Thank you for making this task simple. Chuck g.

open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.