MDE17CSBGW0 Maytag Dryer - Instructions

The tear down on the dryer was more difficult than the instructions and internet showed due to different models used. The kit was not identical to the original parts but close enough to work (I think). The biggest issue we had was getting the drum back in and placed on the wheels where it would turn easily. Overall the repair came together but it was a bit more involved and we anticipated going into the project. The actual noises were caused by the disintegration of the tensioner wheel which broke and was wobbling on the axel.

Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.

replsce

Dryer was making intermittent squealing noises sometimes it was amazingly loud, sometimes not so bad. Still, I figured this couldn't be good so I wanted to find a fix. Read the stories here and everything pointed to the 'idler pulley', so I figured I'd give it a try. For me, access was the hardest part -- my laundry room is small and I can't easily get the dryer out or move it around. Not a problem with the part, just my own setup. Important to note that this repair is best done through the BACK of the unit, not the front. Once I got access to the back (removing AC and Water used for the 'steam dry feature') I also had to disconnect several of the electrical connectors to get the unit fully apart. Good news -- the actual replacement of the pulley took about 1 minute! It was just all of the moving and disassembly that took so long. The original idler pulley had worked its way off of the shaft and was out of place and causing the squealing. All is well now, and I saved a bunch by doing it myself. No more squealing!

Watched a brief video on YouTube and followed step by step. Real easy.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Replaced Lint Screen

After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

pulled out old lint filter. Put in new lint filter.

Popped the panel open & replaced the one that was missing with a new one!

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

remove&replace