Models > MDB9150AWS > Instructions

MDB9150AWS Maytag Dishwasher - Instructions

All installation instructions for MDB9150AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB9150AWS
541-555 of 584
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Now power to control panel; burnt resistors visible

  • Customer: Stephen from Yonkers NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old circuit board. Carefully noted position of wires and connected new board in same way. Also had previously installed new switch and plastic handle from PartSelect. These parts were obviously broken, but apparently were not the only problem. With all parts above replaced, power returned to the control panel and the machine works as new!

Silverware basket had worn out in places and knives were slipping through it

  • Customer: Maria from Benson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply took out the old basket and put in the new basket. Fits beautifully.

Broken latch

  • Customer: Thomas from Globe AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
removed door frame. removed electrical leads. removed broken part. replaced parts in reverse order.

Mice living behind the dishwasher

  • Customer: julie from golden CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Mice were living behind and on top of the dishwasher and destroyed the pad. Had to throw it away. Ordering you was easy, and the pad fit perfectly.

Silverware basket was falling apart.

  • Customer: Richard from Reno NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This is almost a joke. It took 5 seconds to remove the old silverware basket by lifting it from the bottom Rack. Then I spent another 5 seconds to lower the new basket onto the lower rack of the dishwasher. I was a little miffed because the new basket did not match the photo on the Parts Select website, which photo seemed to match the old basket exactly. However it fits, and the wife likes the design of new one better than the old one.

Back Dishrack Guide rail stop was missing

  • Customer: Paula from Venice CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the top rack and looked at the other rail to figure out how the stop should fit into the rail....had to reinstall the rail and rack and reach in from below the rack with the rail extending past the rollers.....took me a little while to figure it out but it worked great.....repair less than $12. ($4 for the part and $7 for shipping the part).

None

  • Customer: Billie from Mount. Airy NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took old basket out put new one in.

Water holes corroded shut

  • Customer: Dary from Colbert WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Whatever you do, don't call a repairman to do this simple replacement task. 1. Remove the lower basket. 2. Locate the round knurled nut holding the spray bar on. (use gloves or a channel lock pliers if it's corroded on) Lift off the spray bar. noting the 'flats' on the bottom of the spray bar. If the knurled nut has lots of corrosion, put it in a container of vinegar for a couple hours. Use screwdriver to remove the metal plates on the ends of the spray bar and install in new one. Then install new one in reverse order. A real piece of cake.

motor running - no spray

  • Customer: Richard from Springfield MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed racks - removed lower wash arm - removed filter screen - removed upper pump cover - removed broken wash impeller - replaced wash impeller - re-installed upper pump cover - re-installed filter screen - re-installed lower wash arm - re-installed racks

grinding noise

  • Customer: Carl E from Lincoln DE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old discharge pump housing and installed new part very easy the video on web made it a very easy and quick job

pump disintegrated

  • Customer: James from St Helens OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding the part cheaper on your website and watch you video it was a peice of cake. and the pump only took like 4 days to get here during the holidays. Jim

Broken roller/axle

  • Customer: Nick from Duluth GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After ordering pasrts, which were shipped quickly--watch the free how to video you had on line. What an assist. It made all the difference. Thanks for such good help

My old silverware basket was breaking away

  • Customer: Amy from WELLSVILLE UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered a new part and simply placed it in where the old part was, make sure you have measured the dimensions of your space, includes a handle for easy lifting, and snap doors for small accessories

Unit was making a grinding noise when pumping out water

  • Customer: Steve from Kenner LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Opened lower panel to better locate noise ( ran in drain mode to pinpoint ). Removed lower tray & started taking apart , found the discharge pump housing had broken on the inside. Ordered parts , they came in a few days & put back together. All works fine & it runs quieter than before it broke

broken silverware basket

  • Customer: Janet from Norwood MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This replacement basket fit perfectly, is well made, and came speedily, as promised!
All Instructions for the MDB9150AWS
541-555 of 584