Models > LEA60AW > Instructions

LEA60AW (PLEA60AW) Amana Dryer - Instructions

All installation instructions for LEA60AW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LEA60AW
496-510 of 520
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

DRYER WAS NOT HEATING

  • Customer: LANORA from SUMMIT LAKE WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
LOOKED ON YOUR WONDERFUL SITE AND FOUND TWO PARTS THAT WERE LISTED AS 80% THE PROBLEM. TOOK A CHANCE AND ORDERED BOTH PARTS. HUSBAND REPLACED BOTH PARTS. AND, YEAH.........WE HAD HEAT. SO NOT SURE WHICH ONE IT NEEDED....BUT, THE PRICE OF YOUR PARTS BEAT THE COSTS OF ANY REPAIR MAN. THANK YOU SO MUCH. WE'RE DRYING CLOTHES AGAIN!!! LK

Loud squeal and squeek

  • Customer: Curran from Cadiz KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took dryer apart and replaced the drum support rollers. This did not work and problem is still there. The videos at the part select did not help since they seemed to be for a different dryer and nothing in them helped in any way to work on my unit. I did get a repair man out and was told that he had not seen one built like this one before.

The dryer had been making the occasional squealing sound for the last year or so, but on it's last use the volume of the squealing increased dramatically along with a new "banging".

  • Customer: Matthew from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The front of the dryer disassemled a bit differently than the video, but once I came to the conclusion I was going to rip it apart, I figured out how it needed to be done. That added about 5 min. to the repair. The main culprit was the idler pulley, it was nearly completely frozen, but I had ordered all the most likely components, so I also changed out the rear support rollers & front glides. The belt was actually in pretty good shape, but I swapped it out also so I wouldn't have to do it in the (near) future. I had to take a 2nd look at the video for belt routing on reassembly. Without tension on the belt it doesn't look like it would work, but once the tension is added the the belt separates so it's not rubbing on itself, like it would appear to do before being tensioned. All and all it was a fairly easy fix and for $47 incl. shipping, much cheaper than a new dryer or even a service call... Thanx

No problems encountered.

  • Customer: Michelle from St. Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The only difference is that I took apart the front frame, that is the white plastic plenum. The videos were of a clean machine, mine was not. I decided to wash the plenum so I took it off the frame. Had it not been the middle of winter in St. Louis, I could have hosed it clean outside, but not this winter. Disassembly allowed me to clean the plenum in the sink.I was extremely impressed with the service and videos. I will be doing business with you in the future and am telling all my DIY family and friends.

Broken belt

  • Customer: JOEL from ALTADENA CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I just followed the intructions from the video on the website. That made the replacement easy.

Squealing

  • Customer: George from Santee CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Pulled the front, loosened the top, released the belt, pulled the tub, pulled the motor, and replaced the idler pulley lever and shaft and the idler pulley wheel, and the belt.

Dryer had an intermittent squeak, then would shut off before the end of cycle.

  • Customer: Steve from Van Buren MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced glides, belt, and rollers, but problem still existed. Next, I purchased a new motor and problem solved! Repairing my dryer was easier than I had previously thought it would be.

replaced roller wheels/ pulley wheel

  • Customer: david from manlius NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I had two repairs, a few days apart while waiting for diagnosis and parts. I watched the videos and followed the steps, simple as that. I was able to replace the rear roller wheels without taking the drum all the way out. I tried the dryer with this 1st fix, some sounds went away but the worst one remained. Took the drum all the way out and replaced the idler pulley wheel just as the video shows. Everything went back together just fine- no extra parts and the dryer is soooooo quiet. My wife thinks I'm a stud for doing this, thank you partselect.com. A caveat, the e rings that hold the wheels on are a big pain to remove and reapply. The snap ring pliers needed to get these off don't always fit in the little openings to remove the ring.Get the smallest size tips if you buy the pliers. My pliers got an "A" for effort, a "D" for results. I used a pair of slotted screwdrivers to manipulate the rings off. Your mileage may vary.

Dryer making noise

  • Customer: Samuel from Tulsa OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The problem was easy to troubleshoot using the PartsSelect diagnostics on the website. After viewing the instructional videos for the parts I suspected I placed the order. When the parts arrived I reviewed the videos prior to attempting the repair. The problem was a drum support roller. I began by removing the top and front panels. The model I have was older than the video and the only trouble I had was that the top panel was screwed in place instead of clips. Once that was figured out the repair was pretty easy. I removed the drum, belt and replaced the Drum Support Rollers and Drum Glides, installed a new belt and reassembled. The parts for this type of repair are so reasonable that some of the parts I replaced were to insure longer life but actually were not in bad shape. Overall this was a very cost effective and relatively easy repair.

Dryer squeaking, shutting down, and difficult starting.

  • Customer: Steve from Van Buren MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was replaced with common hand tools, after replacing roller guides and belt.

Loud sound

  • Customer: Angel R. from Kissimmee FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I knew that it have to be worn out roller drums or the idler pulley with bearing. So, I ordered both items. I watched the repair video to know how to do it. I installed the items and the sound disappeared

Dryer was shacking really bad

  • Customer: Carlos from Rowlett TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it just like the man in the video that was sent via e-mail by ParSelect,.

no power to dryer

  • Customer: Sam from Soldotna AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
found thermal fuse and checked continuity had none so fuse was bad. ordered new one from parts select correct fuse came quickly installed new one and dryer works like new.

The temperature was cold

  • Customer: HOUNG from DES MOINES IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I opened the base door and took out the heater panel and checked with an electrical meter. The high thermal fuse was blown out. I replaced the fuse and run it for five minutes, it was blown out again. I checked wires and nothing was wrong. I replaced another fuse and ran only three loads, it was blown out again. I though that it was a sixteen years old machine, I replaced the whole new heater panel with a new High Limit Thermal Fuse and a new Limit Thermostat. It ran good for 5 minutes test. I will know when I run a few loads in this Friday 4/25/14.

unusual noises

  • Customer: Thomas from katy TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
replaced all above parts, everything seems fine now. Thank You.
All Instructions for the LEA60AW
496-510 of 520