Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
timer was not advancing
First we ordered the multi temperature gas thermostat ( listed as the solution 83% of the time) and the coil kit( 16 %) and replaced those parts as suggested. But that did not work. then we ordered the timer, replaced it in 20 min( 1 wire at a time as suggested) and that fixed the dryer. Thank you.
Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!
I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.
After viewing repair video I used those instructions, after removing drum place new belt on drum, I used scotch tape to hold belt in place, tape belt with 2 inch strip about every foot around drum, leave extra belt that connects to drive motor folded down and taped to drum. After installing drum connect belt to drive motor and roll drum to remove tape. This will keep belt from sliding out of place on drum while installing.
Overall, the repair was pretty easy. I'm a 52 year old woman who has never done drier repair. I replaced both front glides, both drum support roller wheels, the idler pulley wheel and the tumbler and motor belt. Including vacuuming out the inside of dryer and washing down the inside and outside of dryer with cleaning wipes, the whole project took me 2 hours. (if done individually, time would have been 20-30 minutes). You must have correct tools, so I did have to purchase two tools that I didn't have. My only suggestion in replacing the idler pulley wheel and the tumbler/motor belt would be to take the small access panel off the back of the dryer for easier access to the parts.
Belt broke...drum would not turn but there was heat.
Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.
I watched Steve the repairman on u tube then opened up the front of the dryer and noticed the part in my dryer was a little different than the one on the video. So I called in and I was reassured it was what I wanted. When I got the replacement part and before I removed the old part I took pictures of the wiring noticing the wires where changed from left to right I had to make up one of the 12 gauge wires and connectors with parts from the hardware store and the new part was shorter than the old part, but the machine all ready had screw holes where I needed them. I looked at my photos and wired the new part the same way I took the wires off the old part and put it back together and it works like new! saved money! the local guy is $150 to show up and start the clock. I also fixed the blower,EASY!
Removed back panel of machine which exposed badly worn idler pulley. Have had problem before on another dryer so I was sure what problem was before I started. Removed snap washer and cloth washer and then bad pulley.(It was very worn and wobbly).Cleaned shaft with small piece of emery paper and put two drops of oil on shaft and replaced old pulley with new one.Put back washer and snap washer.Drive belt had slipped away from its proper position so I had to remove the front panel of the dryer to place the belt back and realign it on the drum and around the new pulley and the motor drive shaft. Not really that difficult.....Machine now runs like it's brand new.....
Unplug dryer Remove front (2 screws at bottom) From bottom lift out and up to release top bracket Move front panel gently to the left not disturbing wires Remove blower cover with nut driver Remove expansion clip on shaft with expansion clip pliers Remove blower clamp with pliers Slide blower wheel off Replace blower wheel an reassemble
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken belt
I bought this machine in 1984. For the belt to last this long, is extraordinary. The belt comes in a plastic bag with instructions. After removing the front cover(2 screws at the bottom, tip bottom out towards you. Cover unhinges from the top. Lean face against a wall. Don't remove any wires). I then vacuumed the inside thoroughly. Used a parts brush to wipe everything off, and blew out with compressed air. Vacuumed again. A bit obsessive, but gas and dust are not a good combination. So why not take the extra time. There is a continuous mark on the circumference of the drum, left by the original belt. Use this as your guide to locate the new belt. Rotate the drum by hand to make sure it tracks correctly. I also ran the motor with everything open, to make sure everything was cool before I buttoned it up. Also took the time to replace the gas line with a new one, and duct-taped the vent pipe to improve air flow.
