LAT8106AAE Maytag Washer - Instructions

I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.

Found a very stretched, loose pump belt. Was able to pull it off pump pulley and motor pulley easily. Pushed motor assembly toward transmission pulley and removed wider drive belt. Wiped all pulleys clean. There's a double on the motor- one for drive belt, one for pump belt. Removed two hoses from pump using nutdriver. Removed pump. New pump installed. Installed two hoses on new pump. Installed drive new drive belt. Installed pump belt last. Slid pump to near farthest spot in slots. Tested for correct tension by pinching pump belt. Should be able to pinch center so two pump belt sides come within 1/4" of each other just as the spring tensioned motor mount starts to move. Pused washer back into place after external hoses connected. All new hose washers and filters on both hot and cold. Ran, checked for leaks - none! Absolutely perfect. Put front panel back on. No weird noises and drum empties perfectly every time. My wife is so pleased she's doing more loads.

The washing machine would only fill with cold water. This could be a problem with the controls, the wiring or the valve where the external hoses connect. Various tests, which only those with the proper skills & equipment should perform, revealed that the water valve hot side was not opening. UNPLUG the washing machine before doing any work and especially before opening any access panels. NOTE: Label all fasteners & other connections you remove so you know where they should go back. WITH the Washing Machine UNPLUGGED from the wall outlet, I unscrewed the external hot & cold hoses (make sure the water is turned off first!). I unscrewed the panel that holds the valve in a recess in the back of the machine. On this machine, the panel pulls out of the back with the valve attached to it. So I pulled the panel/valve assembly out of the recess and disconnected its electrical connectors (double-check the washing machine is unplugged before doing this). I also disconnected the internal hose that leads from the valve. Finally, I detached the valve from the panel. Installation is the reverse of removal, although it is a good idea to use a new spring clip or hose clamp, whichever you have, to attach the internal hose to your new valve. Once the valve assembly is properly installed, connect your external hoses, double-checking for hot & cold sides carefully, turn the water on and check for leaks. When all that is ok, plug the washer in and test it.

Pryed the front cover off and set it aside. I pulled the top cover off by removing the 1/2" hex screws under the front cover and hinged it back. Removed the agitator set screw with a 1/4" hex nut driver and pulled out the agitator assembly. Had to remove the nut that holds the hub assembly in by using a hammer and punch. There is not much room in the tub so be careful you don't hit the sides. It goes off by turning it clockwise. Then the splash guard comes off and then the inner tub with the top gasket and ring can be lifted out of the washer. The tapered cork covered hub was exposed and it also had to be removed with a hammer and punch clockwise after removing the torx set screw on the side of the hub. The rubber seal was now able to be removed under the hub and on top of the bearing on the outer tub. I had to clean all the accumulated scale off seal and bearing surfaces before putting new parts in (rubber seal, hub assembly, and new locking nut). Everything went back easily. Should be good for another 5-10 years...

After making sure the lines and screens are clean, and there is good water flow thru the hoses to the valves, and there is power to the valve solenoids, (which can be detected by setting to fill and pulling out on the start knob), and hearing a "click" at the valve, you can summize that the valve is weak, or partially blocked internally.
Replace the valve by unpluging the power cord to the machine. Remove the hoses. Remove the screw that attaches the valve mounting plate. Pull the plate and valve out and remove the screw that attaches the valve to the plate. Unplug the wires from the solenoides,[IMPORTANT] noting which wires go to each valve. Remove the rubber hose on top of the valve by squeezing the hose clamp with a pair of pliers, and sliding the clamp up the hose. Now you can pull the hose off. Install the new valve in the reverse order.

Made a 4 prong wrench from a 2" pipe coupling to remove retaining nut. Had to tap retaining washer a few times with hammer and after that it came off very easy. All other work was very easy. parts went together with ease. Saved company several $'s as we were told it was not recomended to repair and should replace washer. Under $100 for parts and a couple hours labor.

I shut off the water feeds and unplugged the washing machine.

I removed the two screws on the bottom panel and lifted it off.

I then lifted the bottom corners of the front plate, pulling out and raising it at about a 45 degree angle, releasing the spring clips which held the top of the front plate to the top of the washing machine and set it aside.

I then located and removed the screws located underneath the top, one in each, of the undersides, of the front corners.

I used duct tape to tape the washing machine lid to the top so that it would not flop open and get damaged as I lifted the top on it's hinges.

I saw, at this point that I needed to open the control panel.

I set the top back down.

On top of the control panel cabinet there are four screws, two on each side. I removed the inner screw from each side and lifted out the control panel and set it down with all it's wires intact.

You will see a hex head screw that is holding the funnel of the water injector in place, I removed it with a nut driver and then reassembled the control panel so that nothing would get damaged as I, once again lifted the top and let it rest open on it's hinges.

I used a long needle nose pliers to squeeze open the hose clamp and loosen and remove the hose so that the complete water injector assembly was free and set it aside.

At this point, I connected the hose of the new unit to it's connector and set the clamp, lowered the top, re-opened the control panel and holding the water injector funnel in place by reaching through the lid I screwed it back into place. From there it was only reversing the steps to reassemble the cabinet.

I was concerned about reinstalling the front panel on it's spring clips but found it to be no problem. I held the front panel at the angle it was in when it popped loose, with the clips resting against the lip of the top and lowered the bottom into place, it just snapped back into place.

The job went fast an well

The motor was easy to replace: unplug the wiring harness, slip off the belts, release the tension springs from the motor carriage with needle-nose pliers, and then unbolt the motor carriage with socket set and remove from the washer. Remove the pulley from the old motor with allen wrench and transfer the carriage to the new motor. Reverse operation for everything and you are back in business. The hardest part was the far back screw holding the carriage, a wobble extension helped.

First, I secured one lid hinge ball in its appropriate position between the lid and the washer. While keeping the first ball in place I placed the other lid hinge ball as close to its intended position as I could get it. Next, I pushed the lid and ball into its position.

Used the online trouble shooting info. Tested as was requested. Found the lid switch. Noticed the fuse was bad. Replaced the fuse and noticed only water was cominf in. Ordered new lid switch assembly. Came with 48 hrs! Replaced and washed clothes! Great service!

Unpluged the washer and removed the top cover. Removed the screws holding the switches and unplug the wires. The process was very easy and the washer worked like a new one.

I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the drive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.

Replaced lid switch assembly. Unplug washer. The console on this washer can be removed without sliding the washer from the wall. Just lean over the drum. Three phillips screws along the top, two machine screws removable using a small socket. Move the console forward to view the lid switch in the middle. Disconnect switch plug. Pop lid switch and plunger out. (Both part of lid switch assembly.) Replace. Connect plug to switch. (Could plug washer in and test at this point. Unplug.) Reassemble.

Replaced the 2 belts according to instructions received with the belts. Very easy repair