Lid Switch Assembly

PartSelect Number PS2003435

This kit includes the lid switch and the plunger. The pin on the lid pushes on the lever of the switch to tell the machine that the lid is closed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Will not agitate.
  • Will not fill with water.
  • Will not drain.
  • Compare At

    $28.86
  • You Save

    $4.81
  • Your Price

    $24.05
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 24 reviews What's this?
1-15 of 24
 

37 of 41 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyA Bit Difficult

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench set

CustomerDaniel from Rio Vista CA

No power on washing machine

I removed the rear panel using a phillip screwdriver and a small wrench. I located the lid switch and popped it loose (no tools needed) and put the new one in. Power came back on washing machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 22 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerBarry from Fallston MD

Washer would not run without opening and closing lid several times.

Replaced lid switch assembly. Unplug washer. The console on this washer can be removed without sliding the washer from the wall. Just lean over the drum. Three phillips screws along the top, two machine screws removable using a small socket. Move the console forward to view the lid switch in the middle. Disconnect switch plug. Pop lid switch and plunger out. (Both part of lid switch assembly.) Replace. Connect plug to switch. (Could plug washer in and test at this point. Unplug.) Reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 22 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerThomas from Doral FL

Washer wouldn't start with lid closed as it should

First, removed two phillips screws that hold instrument cluster in place.
Second, slid instrument cluster off washer.
Third, removed washer lid.
Third, removed faulty switch, removed guide tube and plunger.
Replaced switch, guide tube and plunger.
Removed old and replaced new lid cam.
Reassembled lid and instrument cluster.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 14 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerSUZANNE from MODESTO CA

Washer dead after unbalanced load

Unplugged washer, turned off water supply,Removed the screws in back of console. removed. back plate, unplugged lid switch from console. removed screws holding console to frame of machine. Removed lid by prying the bottom corners out freeing the hinge ball on either side. unscrewed the lid switch from the frame of machine. installed the new plunger screwed into place aligned with lid switch snapped new switch in place, plugged in to console. put screws back into console and put back plate back on turn water supply on plugged in washer started washer which is now working . and the repair guy who never showed up wanted to charge me 50. diagnostic fee when I told him itwas the switch. it cost me less than 50 for all the parts. if you can read you can do

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 7 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerPatrick from Little Rock AR

Slammed lid and broke lid switch

it took a little longer to fix the lid switch becasue the you have to figure out how to install the switch after you takethe old one out. The old one popped out but the new one needs some twisting and pressure. It also is an ackward position to work in on the back of the washer front the front. I think the instructions could have been much better by warning the installer to pay attention when you take the old one out. But it worked and we fixed the problem for $22 and four days of waiting for the part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerKyle from Skiatook OK

Lid switch had went out.

I removed the rear panel of the washer, and removed the lid switch assembly. Then, replaced the old one with the new lid switch and plunger. Put the rear panel back on the washer, and started washing clothes again!!!!!! I think a monkey could have done it....

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJim from Owosso MI

The washer did not start. The only thing that would work was the fascet switch would add water.

I opened up the control panel on the back by removing the 4 screws and then used the print that was inside to check where the power went from the power cord. I checked the power at diferent places and determined that I did not have power coming from the lid switch with the door up or down. You could here the switch click when you opened and closed the door but aperantly it was not working. After going on your web site and looking at the other posts I realixed that there was a fuse link in the switch that was probably blown. I ordered the switch and it was a simple matter to replace when it arrived. The washer works great once more.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerTuong from Sacramento CA

No water fill ,close the lid machine does not work

just unplug the power , disconnect the wire from lid switch ,slide the lid switch assembly out off the switch housing . Then reverse the action I just did above and the machine work again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPeter from Gilbert AZ

Washer shut down while filling w/ lid up

I did a continuity check on the lid switch assembly since it was a) the easist to get to, and b) my wife's descreiption of how rthe washer stopped made me think it had something to do with the lid switch.
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse inside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench set

CustomerFlorencio from Signal Hill CA

Switch not correctly mounted by the previous technician.

Switch material hardened due to old age & broke easily when force fitted. Ordered parts online & in two business day it arrived.

First open the lid & removed the side latch with screw driver carefully. Checked the length of the new plunger with the old one with respect to length & compare the stroke. Slide fit the switch & rectified the play in the plunger pusher with super glue.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerPhilip from Lyndhurst NJ

Washer would not do anything.

Took off the top rear off the washer, Removed the top control section,disconnected the wire harness, snaped out the old switch and installed the new one, connected the wire harness, put everything back together, and it was working again!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEdward from Chamblee GA

Machine would not operate with lid down.

Disconnected power. Then I removed the cover to the console on the back to gain access to the lid switch. Removed the switch assembly by hand and disconnected from electrical plug on machine. Attached new assembly unit to plug and reinserted new assembly onto machine. Reattached cover to console.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJOSEPH from MERRICK NY

Washing machine would not start up

I REMOVED THREE SMALL BOLTS ON THE BACK OF TOP PANEL UNPLUGED ELECTRIC PLUG ON LID SWITCH POPPED OUT OLD SWITCH POPPED IN NEW PLUGGED IN SWITCH PUT TOP BACK ON WITH THE THREE SMALL BOLTS. THE WIFE WAS BACK IN BUSINESS. EASY AS 1 2 3

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

Customergranados from bay point CA

It was not working

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Lid Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBrandon from Grand Island NE

Washer started/then stopped and wouldn't start again

Took the back plate off, popped the old lid switch out and the new one in. Very easy. No problems, saved $100 buck at least doing it myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 24