Models > KUDS01FLSS1 > Instructions

KUDS01FLSS1 KitchenAid Dishwasher - Instructions

All installation instructions for KUDS01FLSS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDS01FLSS1
76-90 of 772
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pump Motor not working

  • Customer: GLENN from CHEPACHET RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
1, I shut off ac circuit breaker.
2.Shut off water supply valve.
3.disconnected water line from inlet valve.
4. disconnect the drainage hose.
5. have plenty of towels to mop up water.
6. Remove racks and disconnect water diverters inside the tub.
7. remove phillips head screws that hold dish washer to counter.
8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope.
9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub.
10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.

It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp!
Left some blood there.

No power to dishwasher

  • Customer: John from Chula Vista CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
First I shut off the breaker for the dishwasher. I had to remove the 6 screws that hold the top part of the dishwasher door to find the panel with the fuse. Then following the instructions that came with the new fuse I cut the wires from the old fuse to remove it. Next I installed the new fuse and attached the wires and then replaced the screws. Turned the breaker back on and everything worked great.

Dishes were not cleaned properly, residue

  • Customer: Francis from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 8 of 10 people found this instruction helpful
I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

Noisy door

  • Customer: John from Minden NV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 7 of 7 people found this instruction helpful
I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Rinse aid dispenser was leaking

  • Customer: Mark from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.

Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.

Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.

The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.

One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.

Dishwasher won't turn on

  • Customer: David from Centreville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
The cycle select buttons on the top of the door worked and would light, however, the power button did not function and did not light. The faulty part ended up not being the control board but the control panel, which included the power button. I spent a good amount of time troubleshooting the problem until I figured this out. The part number was (8531257) Panel-cntl.

dishwasher wasn't fully draining at end of cycle

  • Customer: Richard from Naperville IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 9 of 14 people found this instruction helpful
Removed drain hose to ensure no blockage in drain. No blockage, then removed drain pump cap (where drain hose attaches to drain pump) with allen wrench. Push tab in on drain pump and twist counterclockwise, drain pump came off. Reversed to attach new pump and it works.

motor was very loud...........bearings in motor were beyond repair

  • Customer: Mark from Plymouth WI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 12 of 23 people found this instruction helpful
Replace motor/pump assembly

large leak on start of wash cycle , water leaked at bottom of door

  • Customer: robert from danvers MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
I removed the screws around iner door panel. this allowed me acess to the hex head screws holding the plastic
air inlet and replaced it. the small tabs on the ends of the old inlet had bent
up allowing the water to flow by

dishwasher wasn't cleaning well

  • Customer: Robert from Katy TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

quit pumping water

  • Customer: Robert from West Middlesex PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

DISHWASHER UPPER RACK FALLEN ONE SIDE

  • Customer: Gordon from Lynchburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
POPPED THE OLD HOUSING APART WITH SCREW DRIVER, SAVING INTERNAL PART, INSTALLED PART INTO NEW HOUSING, PLACED IN POSISTION, INSTALLED TWO NEW SCREWS AND IT WORKED LIKE CHARMED. SO SIMPLE, I HAVE ORDERED 2ND PART TO REPLACE OPPOSITE SIDE WHICH IS NOT YET BROKEN. THANKS TO THE TERRIFIC PHONE ASSISTANT WHO CONVINCED ME IT WOULD WORK AND NOT HAVE TO REPLACE THE ENTIRE RACK WHICH WAS SUGGESTED BY A REPAIR MAN......MANY THANKS! ! ! !

Replace old leaky door seal with replacement part

  • Customer: Bob from Lake Forest IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.

Replace Soap Dispenser and Door Balance Kit

  • Customer: Ken from Mission Viejo CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Need torx to remove front panel. There are four screws that hold the control panel that don't need to be removed. If you do remove them, it helps to put the control panel back before you reinstall the front. The six screws that hold the soap dispenser are a very small hex (<1/4, maybe 3/16). It would help to have some small sockets or nut drivers handy for this.

The door balance is easy.

Broken Door Links

  • Customer: Randall from Moreno Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.
All Instructions for the KUDS01FLSS1
76-90 of 772