Models > KUDS01FLSS1 > Instructions

KUDS01FLSS1 KitchenAid Dishwasher - Instructions

All installation instructions for KUDS01FLSS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDS01FLSS1
46-60 of 740
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water pump motor was making a grinding noise

  • Customer: Glenn from Southlake TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 12 of 13 people found this instruction helpful
I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.

Water was leaking.

  • Customer: Phil from Fairfax VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 13 of 18 people found this instruction helpful
This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished.

Stopped cleaning dishes

  • Customer: Steve from Lexington SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
First i remove upper rack held in by 2 clips at end of metal tracks. Compress inside clips and pull up then slide rack out of tracks.Then remove bottom rack just pick it up.Then i removed bottom sprayer by unscrewing center thumb screw. Then removed feeder tube for top sprayer held in place by 2 ea. phillips screws one on celin of tub and one at back of tub. Move tube to the right which unlocks it and remove. This has to be done to expose 4 ea. star screws. Remove screws and pop screen cover off. You have to take a towel and soak up water to expose bottom of inlets and outlets for water. You will then see the chopper blade with metal screen behind it. It is held in place with on star screw to the left of round top cover. Remove cover and pull on chopper blade which will release it from fingers mated from shaft to chopper blade .While pulling on chopper blade toward front of dishwasher pull up on metal screen it will come out. Clean all food particals out i used a shop vac worked well. Be careful not to drop screws in water inlets. The plastic shaft was broken in half by a piece of dental floss wrapped around shaft. I hope this helps it was not that diffacult just hard to work over door.

Drain hose was leaking.

  • Customer: Jason from Lugoff SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 14 of 21 people found this instruction helpful
Switched circuit breaker off.
Removed kick panel.
Removed the dishwasher from counter.
Disconnected drain hose from the pee trap.
Disconnected drain hose from pump.
Installed new drain hose.
Reinstalled dishwasher in counter.
Connected hose at the pee trap.
Turned power back on. test for leaks by running a cycle.
Reinstalled kick panel.

Heater element burned through

  • Customer: dean from wake forest NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 11 people found this instruction helpful
When the dishwasher is pulled out from the cabinet the nuts that hold the element in place are readily accessible. Pull wires off spade terminals, unscrew nuts, remove and replace element. I tightened the (plastic) nuts 3/4 to 1 turn, and used a little silicone gasket maker on the rubber gaskets provided with the new element.
The electronic module is easily replaced by removing the upper part of the dorr panel (top 6 screws). Transfer the wires to it and snap it in place of the old one. This Whirlpool repair set fit perfectly in this Sears dishwasher, and works as it should.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Stopped running in the middle of wash cycle.

  • Customer: Gary from Centennial CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.

Dishes wouldn't dry

  • Customer: George from Lisbon CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 18 people found this instruction helpful
I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

Lid wouldn't close on detergent dispenser

  • Customer: Ellen from Carmichael CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 9 of 9 people found this instruction helpful
Thanks to the previous review of this part, I was able to figure out how to do the replacement myself and saving $150 on a service call. The part is super easy to replace. Remove the screws on the door, lift the outside piece of the door up and off the hinges and then unplug the old piece. I had turned off the electricity to the dishwasher to avoid getting shocked. There were 4 hex nut screws holding the part in, removed those & popped out the old part. Installed the new one, put the door back on and the screws, turned it on and no leaks. This part was so easy to replace, even for a 52 year old woman like myself!

The top rack began to fall out of the track on the right side. Replacing it into the track was not a permanent fix. I could not visually see anything wrong but obviously something was. A web search quickly brought up a picture of that area of our machine. I ordered the part and upon installation,

  • Customer: Ray from Colton OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
I had to getto the side of the machine. After that, it was simply removing 4 screws and removing the old part, replacing the screws and putting the rack back in the track.

Upper button holder allowed bottom wash arm to fall.

  • Customer: Thomas J. from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
After I removed the button holder from the upper wash arm supply line, I put the new botton connecter in it's place. I then held the button in place, slightly bending down the water supply, while bring the wash arm, with the lower support in place, pushing the support onto the button holder. The whole thing took less than 30 seconds.

My dishes were not being cleaned

  • Customer: Molly from Huntsville AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I looked up the most common problem with this model and it was the chopper assembly. I removed everything down to this. Sure enough, mine was broken off and the screen was completely clogged with debris. It was not difficult to replace, but it did take me a few minutes to slide it in to place. Ladies, you can do this. No need to call a repairman! Look up the repair manual and see where the assembly is. I had no idea it was even there. My dishes are spotless now.

Pump/motor assembly make making loud noise & door balance cable broken

  • Customer: David from Bartlett IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 9 of 10 people found this instruction helpful
I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.

The ceramic seal had failed, allowing water to destroy the front motor bearing.

  • Customer: Jerome from Greensburg IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 9 of 10 people found this instruction helpful
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

The dishwasher would not turn on

  • Customer: Mary Ellen from Fairfield VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Very simple. We had to remove the screws holding the metal cover on the inside of the dishwasher to access the electrical panel. Then we disconnected the wires that were connected to the fuse kit, unclipped the kit from the panel, clipped the new one on, and replaced the wires. Then all we had to do was screw the metal cover back onto the inside of the door and it worked just fine.
All Instructions for the KUDS01FLSS1
46-60 of 740