Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDI230B0 > Instructions

KUDI230B0 KitchenAid Dishwasher - Instructions

All installation instructions for KUDI230B0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDI230B0
76-90 of 248
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

upper rack propeller jets lost power

  • Customer: Michael from buffalo, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.

Rubber Water Delivery Tube had decayed over time.

  • Customer: Rene from New Berlin, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Manually remove old tube and simply replace with new tube - no tools!

Hole in the water delivery tube

  • Customer: Michael from Beverly Hills, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Pulled off old tube and slipped on new one.

I replaced the bottom dishrack in my diswasher including axles and wheels

  • Customer: lawrence from langhorne, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
I removed the old rack placed the new axles and wheels on the new rack and rolled it back into the dishwasher . It took about 5 minutes and was very easy.

cap broke

  • Customer: Richard from Sharon, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
screwed it in. Closed the door. Voila, it works!

Not enough water in dishwasher - dishes not clean

  • Customer: Norbert from Westchester, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 1 of 1 people found this instruction helpful
FIrst I shut the water and power off. I took 4 screws off bottom panels of dishwasher. Using pliers I move spring clip of the rubber valve. I disangage the hose and disconnected electrical connection ( two wires ) . Then using two open wrenches ( 3/4" and the other probably 13/16" - not sure ) disconnected the copper tubbing. I replaced the valve i reverse order.I used teflon tape for sealing connections . Everything works good now.

a couple of axles disintegrated so the bottom dish rack wouldn't roll

  • Customer: Anne from Sebastopol, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

roller axle broken, roller fell off

  • Customer: michael from topeka, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

Mom died, selling her house. lower rack of dishwasher with only 2 out of 8 wheels

  • Customer: Theslee from Sharon, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

Rollers came off my bottom rack due to broken axles.

  • Customer: Suzanne from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

Water inlet valve had frozen and cracked

  • Customer: Randall from Ashburn, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
Turn off water and power to the dishwasher. Remove kickboard cover to gain access below the door (2 screws). Water inlet valve was removed using a 5/16 nut driver (1 screw). It is located on the front left side of the dishwasher as you face the appliance. My dishwasher did not need to be pulled out from the cabinet, so using an adjustable wrench removed the supply line. Used a pair of pliers to remove spring clamp on the other line. I then removed the two wires from the clips on the side of the valve. Installation is the reverse, the wires can be reversed with no consequence.

Dishes in top of washer were not getting clean.

  • Customer: Robert from Northport, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

dishes remained dirty after completing wash cycle

  • Customer: Judith from Hinton, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!

Easy as pie!

  • Customer: DeAnn from New Prague, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!

bottom drawer roller replacement

  • Customer: Andrew from Moline, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed the old axles and rollers and snapped in the new ones. Really easy repair.
All Instructions for the KUDI230B0
76-90 of 248