Models > KUDI230B0 > Instructions

KUDI230B0 KitchenAid Dishwasher - Instructions

All installation instructions for KUDI230B0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDI230B0
226-240 of 247
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

hose was cracked

  • Customer: HENRY from CHESTERFIELD MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
old hose fell off. heated up new hose in hot water one end only and it went right on.

dishwasher wasn't draining

  • Customer: Lola from Graeagle CA
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video

Dishwasher Stopped then only made a humming noise.

  • Customer: Michael from Marysville PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

Dishwasher made crunching/grinding noise, then would not drain

  • Customer: Carole from Holland PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Ordered the drain and wash impeller/chopper kit, which I received in 2 days. Great service. I watched the video on how to install the parts and the video was very clear and made the job seem easy. And it was easy, except for getting the impeller screw out. The impeller top was very brittle and pieces kept breaking off when trying to hold it with the adjustable wrench. Robo Grips didn't work any better. The only thing that finally got that screw out was a long handled socket wrench with an extension. You need the extra leverage if the screw is really stuck. Also note that the balls are definitely in the wrong place in the video. You need to remove them when doing the repair, then drop them back into the hole in the gasket/seal cover for the impeller after it is replaced. They will sit side-by-side if installed correctly. Turns out that the crunching/grinding noise was the chopper trying to chop up one of the clips that holds the silverware basket on the bottom rack. It was in many small pieces and had ripped up and split the impeller shaft.The dishwasher is back together and running perfectly. Thank you for very clear instructions on replacing the part and the quick delivery of the product.

The rubber delivery tube was worn out

  • Customer: Mark from Deer Park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I disconnected the tube. Before connecting the new delivery tube I softened both ends by applying heat from a hair dryer. Both ends of the tube slid right on to the ends and I was back in business!!!

Ordered axles to replace several originals which had broken.

  • Customer: Dee from Bryn Mawr PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The installation video is excellent. What should have been a simple fix proved to be difficult for me. Perhaps a function of not enough hand strength to "snap" the axles in place. After trying to use a screwdriver to pry open a side enough to slide on and soaking in hot water to make the axles more pliable -- neither of which worked -- I turned the rack on its side, inserted the axle in the opening and then stepped on it. Voila! That worked beautifully and the next two were easy using the "stand-on-it" method. For anyone with a similar issue as far as hand strength, I recommend this method.

Coating on lower rack was rusty

  • Customer: Jack from Dayton OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I found a video that showed how to take the wheels and axles off. After that it was easy - for me using gloves helped on the axles. I am not a DIY but since I previously used the repair kit on the rusted spots 2x in the past 6 years decided it was time to replace. Axles went on the new rack easier after I soaked them in hot water. Wheels popped right on. Then I discovered my silverware basket didn't fit. After scouring the internet to see which style would fit, I studied the location in the front of the rack and found that only one prong was preventing the basket from sliding in. I bent that one prong forward enough to allow the old basket to slide into the same location in the front of the new rack. I did notice that the new rack is quite a bit lighter than the old rack - that is what probably made it easier to bend the prong so I could get the old basket in.

missing rinse dispenser cap

  • Customer: Terry from Pompano Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Sorry to say that all I did was screw the cap on in about 3 seconds. Not a repair.

High limit thermosat blowes when on santi. rinse

  • Customer: Frank from Bellerose Manor NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove blown high limit therm.and replace with the new high limit

Dishwasher grinding noise

  • Customer: John from Roebling NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Heard a grinding noise in our dishwasher one night recently while it was in the drain mode. Water wasn't draining out so I had to siphon it out with a tube, cup, and rags, then looked up information about the washer/dryer on the internet and found PartsSelect. I watched the repair video they provided and decided to give the repair a try. I began to remove all the necessary parts following the instructional video.
The hardest part of the job came early on, and once that was completed the rest of the job was a cinch. The center screw holding the upper impeller was the hardest part to remove. I tried to use the adjustable wrench on the hex shaped nut molded to the impeller while turning the screw, but that old screw was so tight I was afraid I'd strip the molded impeller nut.
I then tried a 1 inch nut without the driver attached to it but with a pair of vice grips clamped at about 45 degree angle on the 1 inch nut and set on the molded impeller nut while at the same time trying to remove the screw by putting the small nut driver through the top of the 1 inch nut and turning it. No luck there either. It would not budge.
By this time I was entertaining the idea of buying a new 5 to 800.00 dishwasher.
Well I had nothing else to lose except 5 to $800.00, so I reverted to caveman technology.
I ended up using a small chisel and wood mallet to get the impeller off the shaft. Since the impeller is made of a rubber like material, it came off easily in pieces using some careful strikes with the hammer on the impellers molded nut. When this was complete, I unscrewed and removed the filter housing.
The impeller screw, which was still in the motor shaft, and was removed 'after' this because there was no impeller or filter chamber in the way. There was a small space between the screw and the motor shaft since the impeller was removed from around that screw so I first tightened it a little bit, then finally was able to loosen the screw. You would think that screw had been super glued into that shaft but it finally came out. After that I removed the chopper blade and found that the spring attached to it was bent and had tore the shaft of the 'lower' drain impeller to pieces. After cleaning up the impeller pieces I ordered the drain and wash impeller kit from PartSellect. It arrived in a couple of days and the new parts installation went quickly.I was especiially relieved that the new screw and impeller went on without a hitch.
I didn't use the new shaft seal provided because it was a different height then the original seal and wouldn't allow the cover to the drain impeller to seat properly. The height of the new seal also caused the new drain impeller to push or spring up too high.The original seal looked fine so I used that and it worked just fine also. Started the dishwasher up for a test and it all worked flawlessly. No noise no leaks. This was my first washer dryer repair. Following the Part Sellect instructional video with Steve explaining while doing the removal of old and installation of the new parts was a breeze. SO, here's my conclusion. Folks, for under $50.00 I saved a lot of money and expect that I'll get at least a few years more use from this old dishwasher. Thanks again to PartSelect and Steve for your help.

Dishwasher wouldn't drain

  • Customer: Roy from Powell OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

Dishes not clean and soap dispenser not completely rinsed out.

  • Customer: James from Trafalgar IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

Axle-rack is too stiff to snap on the dish rack by hand.

  • Customer: Stanley from Potomac MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Use plier to gently snap on the axle-rack.

Leaking

  • Customer: Robert from Nuevo CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Thee dishwasher came apart very easy, had no problems. Found out where it was leaking around the seal. Ordered parts and they arrived very promptly. Had a few little glitches when I was putting it back together. One of the screws stripped and a larger screw solved the problem. I have a lot of patience, so it worked out fine. Bob.

Water Delivery Tube old and brittle and full of holes.

  • Customer: Donna from Dayton OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched "PartSelect" video showing how to remove the old tube and install the new one. Also read what others said about warming the tube with a hair dryer to make the rubber more flexible -- as you had to stretch the rubber to get it to go over the plastic parts that it attached to. I ordered the part around 3 PM and received it around 10:30 AM the next day. Excellent service!
All Instructions for the KUDI230B0
226-240 of 247