KUDG23HB0 KitchenAid Dishwasher - Instructions

Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

FIrst I shut the water and power off. I took 4 screws off bottom panels of dishwasher. Using pliers I move spring clip of the rubber valve. I disangage the hose and disconnected electrical connection ( two wires ) . Then using two open wrenches ( 3/4" and the other probably 13/16" - not sure ) disconnected the copper tubbing. I replaced the valve i reverse order.I used teflon tape for sealing connections . Everything works good now.

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

Turn off water and power to the dishwasher. Remove kickboard cover to gain access below the door (2 screws). Water inlet valve was removed using a 5/16 nut driver (1 screw). It is located on the front left side of the dishwasher as you face the appliance. My dishwasher did not need to be pulled out from the cabinet, so using an adjustable wrench removed the supply line. Used a pair of pliers to remove spring clamp on the other line. I then removed the two wires from the clips on the side of the valve. Installation is the reverse, the wires can be reversed with no consequence.

Loved how easy it was to deal with you!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!

Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!

So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.