KUDA22SWWH0 KitchenAid Dishwasher - Instructions

Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

Loved how easy it was to deal with you!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!

I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!

First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.

I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.

It was simple. I simply replaced the old water tube with the new one you sent, and it works like new. Piece of cake.

Removed old tube.

New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.

just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays