KRFF15KSWHY0 KitchenAid Freezer - Instructions

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.

First I watched PartSelect videos that Bing rounded up describing the repair. I saw how to remove an ice maker, the back panel of the freezer, and remove and replace the fan and motor. The order was made on Wednesday, arrived Thursday and installed Friday. I took the time to clean everything while it was apart. The refrigerator is running like a new one, quietly and colder than before. It felt good to be able to do it my self. My wife was sure the refrigerator was going to stop running, but I proved her wrong.

Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

I basically followed the step-by-step instructions at the parts order website. I removed the shelves and rear panels to access the fan. I noted the color coding on the wires and terminals, removed the two retainer screws, removed the old fan from the mounting bracket, installed the new fan using the rubber anti-vibration mounts, pressed-on the fan to the center drive shaft and re-installed the assembly to the back wall. I simply replaced the rear panels and shelves and plugged in the fridge. The only issue I had was the distance needed to press on the fan blade to preclude fan noise, which I found by trial and error, before re-installing the panels.

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

Unplugged freezer, removed lower shelving, removed panel covering the evaporator motor. Unpluged three wires connected to fan assem and removed. Did not install new wiring that came with kit but installed new motor/fan and reconnected existing wiring. Problem gone!