Models > KHWS02RMT3 > Instructions

KHWS02RMT3 KitchenAid Washer - Instructions

All installation instructions for KHWS02RMT3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHWS02RMT3
61-75 of 167
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

OEM hinge was rusting to the point that it broke on one side

  • Customer: Gary from Peyton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
The repair was rather easy. It involved the removal of all the bolts around the glass door and only the bolts on the hinge conected to the washer itself. there was a bit of alignment problem when put back together, minor rubbing, but not much. The door now works close to as good as new.

Front seal leaked

  • Customer: Ramon from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 11 people found this instruction helpful
It was so easy my wife replaced the part.

error F28 in mid cycle

  • Customer: Nicholas from Boothwyn PA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
check error code : no water flow
pulled hoses [hot& cold] to clean screen in line.
pulled flow meter out from under top of hood to clean and check free wheel movement inside.
still error code F28 in mid wash cycle. called in and talk with service: he explained that hot& cold water valve was opening to slow or not enough for flow meter to read full presure. I replace water valve and flow meter. washer is doing fine. [I was getting readly to go in futher down the line and get new controler. talking to service stop me from spending a lot of money. THANK YOU

F-20 ERROR CODE

  • Customer: GARY from CLARKSVILLE IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
TAKE OFF TOP OF WASHER AND THE FLOWMETER IS IN THE BACK LEFTHAND CORNER ON THE TOP OF THE WASHER.REPLACED THE WATER LEVEL SWITCH ON THE TOP RIGHTHAND OF THE MACHINE ALSO. GOT ABOUT 150.00 TOTAL INVESTED W/SERVICE CALL FROM LOCAL TECH.F-20 HAS NOT CAME BACK YET. I HOPED IT FIXED IT WASHER IS ONLY 3 YRS. OLD. -GD

Pump not working

  • Customer: Darrell from Lady Lake FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Replaced pump

Shaft in water pump broke

  • Customer: Jeffrey from Adrian MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 3 of 3 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

baffle connectors worn off

  • Customer: richard from chetek WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Placed baffle inside of washer and pulled to lock into place. EASY!!!

The washer was unable to run without door locking

  • Customer: MICHAEL from DERIDDER LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .

door would not latch , and lights on front just flashed

  • Customer: FRANCIS from leesburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Pump not draining the water out.

  • Customer: Martin from Kotzebue AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

Washer wouldn't drain

  • Customer: Jeff from Barrington RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Easily. 4 Screws. 2 Clamps.

wont pump the water out

  • Customer: Paul from Corning NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

Displayed F and H alternately

  • Customer: LAVERNE from NIANTIC CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Door latch would not lock

  • Customer: William from Victorville CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.

the pump wasnt puping out the water

  • Customer: Evette from Mayfield NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 3 people found this instruction helpful
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
All Instructions for the KHWS02RMT3
61-75 of 167