Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Ordering was simple Recieved part day after shipping. 3 days sooner than I expected. Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done. Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.
When you open the door at the start the fan wood come on
I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it
Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.
BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.
first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed
Bulbs broke off in socket, socket would not come out
I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first. thanks you
Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.
remove 2 screws from top of grille; remove grille by moving it to the left and then away. remove old filter by lifting the front edge and then pull out, and replace it wih a new one using the reverse order of the above. replace grrille and screws. The repair is a 'no brainer'.
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.
Glass turntable stoped turning due to broken coupler
Pulled out broken one with fingers, put on new one with fingers, it did not have anything preventing it from just slipping on. Didn't need to take anything apart to install me part.
I simply pulled the old coupler off the moter shaft after removing glass turntable plate. The coupler lifted right out since it was fractured. Luckily all peices came out attached. Typically you would need to remove the bottom access panel on the microwave and remove the turntable motor to install the new coupler. However you can simply snap off the extra plastic piece that is molded to the coupler to allow for an easy push down onto the shaft from the inside of the microwave cooking area where the coupler fits onto the moter. Piece of cake. I don't believe there is any danger in shortcutting this because the weight of the glass plate will hold it in place.