Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer was not staying cold enugh for ice maker to work. Discovered fan was not working to cool condensor. Fan motor would only run if manually turned.
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
Door flap not opening correctly and noise when pushing button for water
This repair was relatively easy due to the instructions provided and took about 15 minutes. Originally, I had bought a door flap thinking that was the problem (a small plastic piece on the flap had broken off) but after replacing that the assembly still would not allow ice flow. I then purchased the kit including solenoid and the repair worked. I had a bad solenoid all along. My suggestion is to replace the entire kit rather than one part as it is likely all parts need replacement.
Read wiring diagram found what would stop power to compressor. Removed thermostat checked for continuity which there was none no matter what position dial was in. Checked operation of remaining components in the refrigerator by jumping the two wires together that are connected to the thermostat, plugged refrigerator back in and compressor kicked right on.
From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.
First I unplugged the refrigerator, then next I removed the (4) screws holding in the inside back panel section of the freezer covering the cooling coils, the fan motor is attached to the removable panel. I then unplugged the wiring harness to the fan motor which allows you to completely remove the freezer inside panel in order to replace the fan motor on a counter top or benchtop. I removed the (3) spade terminal wiring from the fan motor and the nuts holding the motor on the frame. I then replaced the fan motor and blade the same way I had removed the old one, and then reattached the wiring terminals on the same terminals as the existing motor, making sure that black, red, and green do not get mixed up. I placed the rear panel back inside freezer and plugged in the wiring harness, fit panel back to original position and reinstalled the (4) panel screws. I once again plugged in the refrigerator and restored power. Everything is working fine.
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Extremely easy install. Just popped off the cover located on the side of the compressor. Noted placement of the wires on the overload and relay. Took a small screwdriver to slide both from the electrical pins on the compressor...take care doing this. Unplugged the wires, plugged the new components to the wires and installed to the compressor. Plugged in the frig and the compressor came on. Not sure why these went out to begin with but the fix was extremely easy and saved me the expense of a repair man.
My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.
As the previous users have stated, remove the ice tray, then remove the ice bin enclosure. Watch for the screws that are used to mount the enclosure. As you slide the enclosure forward, go slowly, there is a wiring connector at the back, you will need to un-plug this connector. The solenoid assy is kind of tricky, as it is spring loaded, but easy to figure out. As previously mentioned, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). Be careful with that, as it is hard to hold on to the shaft while getting the yoke off. Now remount the motor, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, slide it the rest of the way in, tighten the screws, and you are ready to make ice again. Approx 30 minute job.
Water dispenser and ice maker wouldn't work (bought the fridge u$ed)
I bought the following parts:
PS109042 Double Outlet Water Valve PS46363 Dual Outlet Water Valve Kit
When I bought the fridge, the part that PS109042 replaces was cracked and leaking water badly. When I ordered the replacement part, I got confused and ordered PS46363 by mistake. The original parts look similar even when side by side, but the replacement parts are revised drastically.
PS46363 is for the line that is between the water source and the water filter. The original lines from the filter are split (the original part has two inlets) and pipe to one inlet. You'll have to cut your hose right before it forks. The directions that come with the part are very straight-forward.
PS109042 actually distributes the filtered water to the water dispenser and icemaker. The old part had plastic fittings that held the water hosing to the part. The new part has no plastic fittings, yet holds the hosing to the part tightly. The directions that come with the part are very short and concise.
I also replaced the factory water filter with a Brita replacement (they are cheaper and I've used Brita filters before...they are solid).
All in all, I spent less than $100 on fixing a $500 used fridge that works as good as new. My wife was initially doubtful but fairly satisfied with the cost of the parts and the simplicity of installing them.
noisy fan motor, fridge & freezer not holding temp
I took off the ice maker, disconected the wiring, took out the back of the freezer and took out the fan motor. Harder than I thought because of all the wiring back there, light, fan assembly etc. After that it was easy, took out the old motor & installed the new one. Runs much quieter now, and the fridge & freezer are much colder. I did this for less than the price of a service call by a repair shop.
Easy to diagnose problem because there was water to the water dispenser but none to the newly installed icemaker. Originally did attempt to clean the solenoid but found the plunger assembly damaged.
New part arrived sooner than I thought it would. Takes about as much time to remove the lower vent cover as to replace the valve. Remove the electrical plug from the wall, valve off the main water supply, remove lower vent cover, disconnect the supply hose from refrigerator valve assembly, remove one hex head mounting screw and you have both water valves in your hands. Identify the valve the supplies water to the filter and the one that supplies water to the icemaker/water dispenser. Then confirm which plastic water supply line goes to the water dispenser and which goes to the icemaker. Hose diameters are different but it is good to know. Disconnect the plastic water supply lines from both the ice dispenser and the icemaker portions of the valve. Replacement solenoid valve does not have thread on type compression fittings. Snip about an inch off of each hose and then press into the appropriate valve orifice.
Making sure the plastic supply lines do not get crimped, remount the valve assembly, reattach the supply hose, valve on the water and check for leaks. No leaks, reinstall dust cover and plug the refrigerator back in.
Move the unit back in place and then take a long deserved beer out and have a celebratory toast for a job well done.
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!
Freezer and fresh food sections too warm, with control settings at coolest.
Thanks to previously posted PartSelect stories, I had a good idea on how to proceed. This component, as others have suggested, is clearly a piece of junk. This is the third time it has been replaced, once under warranty, again in a service call for $160 and now by me, with a PartSelect unit for $52. The circuit board, with integral relay, resides in the extreme upper right hand corner of the fresh food compartment. Remove upper shelf. Remove white plastic control cover through which the lights illuminate the compartment. Finger grips at both sides at rear. Slide forward about an inch to clear the tabs visible at the rear, then tilt down and off. The owners' manual describes this at "Changing the Light Bulbs". It also gets the lightbulb description wrong, but .......... Now remove the hex head screw facing you at the rear center. Then get its two cousins which are vertically positioned to hold the front of this housing up into the roof. They're left and right, just rearwards of the ends of the control setting dial. These three tapping screws which you now have in hand are about 1 1/4" long. Next, there are two Phillips head screws, also into the roof, whice are just to the rear of the two light sockets. Removing these, and the left one is awkward, frees up the control totally except for the wiring harness, which restrains it at the rear. No matter, just tilt the unit down so that the front lip is pointed down towards you. The piece-o-crap board is at the right rear. Pop off the connector, takes some force, and put in your new module. Order another one now, you will need it. The service tech who changed out my next-to-last one left a circuit diagram back there with the new control, like saying "I'll be back."