JJW8527AAW Jenn-Air Wall Oven - Instructions

Removed 4 screws that hold the clock assembly panel in place. Removed the defective part and replaced it with the new part. The wiring connectors were almost impossible to incorrectly connect.
Easy and saved $ 100

My friend actually replaced this but it was really quick and easy. If I'd had to do it myself, I think I could have because it came with the simpilist step-by-step directions! The best part of all was that I ordered it online on Monday and had it on Tuesday....during Christmas week!! Unbelievable service. Will definitely recommend this company to anyone needing any appliance parts!

It was nice to be able to find this site and see that my problem was the same as others and they had all solved it with replacing the control module. So I ordered the part. Received it. Removed the 4 screws on the panel, then removed the connectors, then removed the bolts holding the control panel on the board. Replaced control panel and hooked it all back up. Very easy and was working in 15 minutes.

Very easy to replace. open oven door,
remove four screws holding oven control
cover, remove 4 1/2 in screws holding
display unit with a nut wrench, unplug
three connectors. intall new unit, replug
connectors and replace screw in reverse
order.

We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!

I unscrewed the cover on the oven. Used a socket to remove the electronic circuit board and unplug the electrical connectors. Then I plugged the new board in and reattached it.

Some of the connector prongs got bent in shipping I guess but I was able to straighten them.

I have a stacked microwave and oven. Removing the oven control panel was easy, removing the circuit board was easy, Replacing the wiring strips and board was easy. Reataching the control panel with the four screws was the hardest part., Gotta wirk upside down!! Saved about $200 doing it myself.

1. Remove 4 screws at the bottom of the control panel (above oven door) that hold it in place.
2. Pull the control panel away from oven and lift to remove.
3. Unplug two wire connectors to remove panel from oven.
4. Unplug two wire connectors from the clock panel. Used a putty knife to disengage the connector locking mechanism.
5. Remove 4 screws holding clock in place.
6-10. Installed new clock in reverse order of removal.

It was very easy, it took less than 10 minutes
just a few screws.

Turned off power to the oven
I removed the three screws holding the front panel on, then tilted it slightly and removed it. Then gently pulled the three wiring clips off the posts and set the panel down. Removed the 4 screws holing the dispay with a 1/4 " nutdriver and replaced the screen and reversed the procedure. Turned the power on and it worked!!

As per instructions on the web, removed 3 screws to get round metal plate out to get to wires, removed 2 screws to get element out, it was a breeze.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

The display belongs to the convection oven. We still could use the oven because we knew how all the buttons and beeps worked, but we replaced the control module because we couldn't sell the house without it. Here's how to replace the module:
- Remove the bezel on the microwave above the oven (4 screws on the sides).
- Now you can remove four up-facing screws on top of the control panel. Don't unwire the panel, just lay it face-down on the topmost oven shelf, as one of the others above advised.
- Looking at the back of the clock module, remove the two connectors. The larger one is difficult to pull. Just force each end gently straight up with a flat screwdriver.
- Remove the screws holding the clock in place. They're at the two ends.
- Swap the clocks and put everything back.
I bought this module from PartSelect because of all the customer feedback you see here. It gave me the confidence to do it myself.

shut power to unit removed front top cover,four screws holding it down.diconnect element and install new one.its that easy.

first of all you had super fast shipping only 2 days from order to repaired complete. removed 2 screws and 2 wires replaced old heat coil with new one replaced 2 wires and 2 screws less than 5 mins.