JGP333DET3WW General Electric Cooktop - Instructions
Sections
Parts
Questions & Answers
Symptoms
Videos
Instructions
All Instructions for the JGP333DET3WW
Burner had uneven flames
Too easy a five year old could do it
Parts Used:
Akshay from Bridgeton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
3 of 5 people
found this instruction helpful.
Thank you for voting!
The eye would not light
Remove the existing burner and install the replacement.
Parts Used:
Solomon A from COLLEGE PARK, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
2 of 2 people
found this instruction helpful.
Thank you for voting!
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure. I do use silicone to help hold the foot but it still won't hold
Parts Used:
Richard from Stratham, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 3 people
found this instruction helpful.
Thank you for voting!
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Parts Used:
Terry L from Puyallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 3 people
found this instruction helpful.
Thank you for voting!
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Parts Used:
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
3 of 7 people
found this instruction helpful.
Thank you for voting!
gas burners not heating evenly
remove old burner, put new in place
Parts Used:
Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
1 person
found this instruction helpful.
Thank you for voting!
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Parts Used:
Gary from HENDERSONVLLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
The electrode had broke
I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode. I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
Parts Used:
O.Robert from Montrose, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 person
found this instruction helpful.
Thank you for voting!
burner cap wasn't working proper.
took burner off installed new one thank you for fast shipping
Parts Used:
GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
1 person
found this instruction helpful.
Thank you for voting!
Failed ignighter
Repair is easy. The keeper ring installation while holding the spring down was tricky. An extra set of hands is helpful in holding and replacing the keeper ring.
Parts Used:
Connie from WESTFIELD, IN
Total Repair Time:
15 - 30 mins
1 person
found this instruction helpful.
Thank you for voting!
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Parts Used:
Mohammad from BARTLETT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Parts Used:
Robert from SOUTH ELGIN, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time. Otherwise everything was great!
Parts Used:
Rita from ST AUGUSTINE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Parts Used:
Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
1 of 2 people
found this instruction helpful.
Thank you for voting!
All Instructions for the JGP333DET3WW