2353327-2-S-GE-WB02T10461-Grate Foot
2353327-2-S-GE-WB02T10461-Grate Foot 2353327-1-S-GE-WB02T10461-Grate Foot

Grate Foot

PartSelect Number PS2353327

Sold individually. The grate foot is located under the grate to protect the stove top.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Touchpad does not respond.
  • Compare At

    $2.02
  • You Save

    $.34
  • Your Price

    $1.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 13 reviews What's this?
1-13 of 13
 

27 of 36 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerFRANK from MEMPHIS TN

The cooktop had a shorted out burner control.

Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 11 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerKathryn from Star City AR

Grate foot had worn out

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

Customerfrank from cathedral city CA

Igniter wasn't lighting burner

Repair to range went real well, Lifted range from

counter. Removed eight screws that secure burner

assembly. Lifted burners from it's position, and

removed igniters. Installed heat srink at burner

connections so as to ensure high voltage would

have no leaks. Removed insulation, and installed

spark module.. Reassembled unit, placed in

counter cut out, put 110 volt cord into outlet.

Tested all burners, everything worked great..

The repair took about hour and 15 minutes.

Have fun and be careful...... THE END

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsWrench set

CustomerGina from Atlanta GA

Upper left rack roller broke, had to replace rack adjuster assembly

First I had to take out the end caps on both sides of the upper rack - easy enough - you push in the direction of the arrows and they open up and come off. Then I took the rack off. Using the smallest allen wrench I could find in my ex-husband's set that he left behind (yay!), unscrewed the old rack assembly. The (blue) adjuster level doohickey popped out when the old assembly came off, but it was easy enough to fit that back in properly by looking at the right-hand one that was still in place. All I had to do was fit the new rack assembly into place, put back a few screws, and slide the rack back into place. Put the end caps back on and you're done. Maytag should offer free replacements for this part, IMO- the wheels are too flimsy to begin with, our dishwasher is only four years old, and the new part is pricey, at $29.45 a pop.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRichard from Stratham NH

Feet keep falling off

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAnne from Jacksonville FL

After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerTerry L from Puyallup WA

Rubber grate foot worn or missing.

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerROBERT from CYPRESS TX

Very easy

there were no grate pads so it was easy to add them.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerShelley from Wolfeboro NH

I had a few broken parts on my cooktop

Ordered the parts online. They came in just a few days and all 3 repairs took me less than 10 minutes!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJohn from Tijeras NM

Grate foot bdroke off allowing grate to scratch cooktop

Used scribe to remove grate foot plug still in grate inserted new foot.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerHarold from Broadalbin NY

The grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerChelagh from Fredericksburg VA

The grate foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 7 people found this instruction helpful

Parts Used

  • Grate Foot

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerGene from Simi Valley CA

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-13 of 13