JGD8130ADS Jenn-Air Cooktop - Instructions

Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.

Prepare a flat area with newspaper, a screwdriver, and a small bowl for the screws, and a small wire brush (if you want to clean as you go). I also recommend taking photos as you proceed, for reference.

ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.

Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.

Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).

Remove the burner tubes and washers.

Carefully remove the igniter connectors from igniter.

Remove the end of the assembly.

Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.

The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.

Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!

Attach the igniter connector to the igniters.

Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.

Install entire assembly into cook top, check igniter and burner operation.

Glass cleaner is great for cleaning the new porcelain surface.

Disassembled old part put new one in reversed order

took out burner and remove ignite r and reinstall a new one simple as that

Still not fixed. Waited about a year for the part to arrive, due to "COVID supply chain issue". Part finally arrived and was missing a sub component (ironically the worn out part). Now awaiting a reorder confirmation that this is being sent along with a return mailing label.
The re-order required me to obtain a better picture of the part from your competitor's web site, to prove the part sent was defective as your site was inadequate. My first call on this issue failed because of an absence of the better picture.
The 2nd call to customer service was very understanding and professional but I have yet to receive any confirmation on this re-order in the past 5 days.

Removed Stove cartridge from stove-top.

Unfastened bottom screws, I recall 6.

Removed cover.

Removed two screws to igniter.

Used needle nose pliers to remove connectors x 2.

Had to drill to enlarge the mounting screws to new ignitor, then screwed it in place

Connected the two wires to each igniter.

Replaced cover n screws.
Reinstalled cartridge.

Bingo

I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.

Remove the 2 burner assembly by gently lifting the rear burner and pull towards the back of the stove and the entire 2 burner assembly will slide out. Turn assembly up side down, remove all the screw on the cover with a philip screwdriver and remove cover. Once opened, you will see the ignighter, remove the 2 screws holding it in place, remove and replace the ignighter and secure with two screws. Follow the 2 lead wires and remove and replace with the new wires, simply pull off old and push on new wires. Replace the cover and all the screws, slide it back onto the stove and you will have ignition! Simple install, takes about 20-30 minures. If both burners are out, this is probably the problem. If only 1 burner is out, you probably need to replace the stove burner spark.

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.

It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.

throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover