Models > JGD8130ADS > Instructions

JGD8130ADS Jenn-Air Cooktop - Instructions

All installation instructions for JGD8130ADS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGD8130ADS
31-45 of 82
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

fan switch pushed through, plastic housing broken

  • Customer: Lois from Alpharetta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

smell of a dead animal

  • Customer: Duane from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

the shell if the igniter was broken

  • Customer: tao from Frisco TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.

vent fan cloging up

  • Customer: JAMES from McALESTER OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Fan on built in Jenn-Air went out.

  • Customer: Katrina from Coos Bay OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
ordered part, called friend who does odd jobs, and he came and turned off electric, unscrewed the area, pulled out old plug, plugged in the new. Turned on electric and walla, fan works !!!! thank you very much. Part arrived in very short length of time. I was surprised.

Fan stopped working.

  • Customer: Gregory from Hickman KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed the two screws that hold the switch in place. I then pulled the switch out about 3 inches and disconnected the three wires from the old switch and replaced the new switch....

The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.

  • Customer: Martyn from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Needed to replace the grease filter!

  • Customer: Colette from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Followed the directions. Piece of cake!!

terminal spade wrong size on range wiring to fit module

  • Customer: wilber from oshkosh WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 7 people found this instruction helpful
cut off terminals and replaced with the right size one's stove lights every time now wlrowe

Grease filter was torn and bent

  • Customer: Brent from Rancho Santa Fe CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I just lifted out old filter, and put in new one.

Filter needed replacement. Old one was falling apart.

  • Customer: Sophie from Warrenton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed old filter, dropped in the new one.
(This really was not a "repair")

Old filter couldn't be cleaned

  • Customer: William from Goshen NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???

Filter replacement.

  • Customer: Gerald from Maplefalls WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Remove and replace grease filter.

switch too big for hole

  • Customer: Darrell from Moultrie GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.

Old grease filter had hole wore through

  • Customer: Michael from Mountain Iron MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled the old one out & inserted the new one. Less than five minutes.
All Instructions for the JGD8130ADS
31-45 of 82