Models > JGD8130ADS > Instructions

JGD8130ADS Jenn-Air Cooktop - Instructions

All installation instructions for JGD8130ADS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JGD8130ADS
61-75 of 82
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replacement

  • Customer: Barb from Holladay UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

Filter was very old and falling apart.

  • Customer: June S from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

The high/low fan switch was inoperable.

  • Customer: Bam from Wilmington NC
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The available replacement switch is a bit too large to fit into the hole on the original face plate which must be kept as it also mounts the 4 burner dials and the “on” light.
A local machine shop was able to make the original hole large enough to accommodate the new switch. Total time to detach and reassemble the original face plate, less than 2 hours. Other than the new switch being black, it looks original. (The 2 smaller face plates provided with the new switch were not needed.)

The old burner was rusted through and the gas port came loose from it.

  • Customer: Roger from Syracuse IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
To gain access to the burner, the bottom of the double burner unit had to be removed (7 screws). Once this was achieved, it was a simple matter of removing the old burner head which is captured with three lobes that engage the unit much like a thread,(which in my case was stuck in because of rust and had to be persuaded with a pipe wrench). The new burner was installed with hand pressure only, and once the gas flange was remounted and the ignitor hooked up, I just re-attached the bottom of the unit and viola!

Wore out burner and igniter

  • Customer: Bruce from Vashon WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
New burner and igniter.....actually it was very easy to to fix

Replacement of top burner igniter

  • Customer: Godfrey from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3

Gas burner would not light-had to use lighter

  • Customer: James from Osage Beach MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As described for the part. Easy repair. Easy to diagnose thanks to feedback from another customer of yours. Part was received super fast.

BURNER IGNITER AND BURNER

  • Customer: ROBERT from MADISON FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
DIS MANTEL BURNER UNIT REMOVED BURNER REPLACED BURNER AND IGNITER

Fan Switch burned out on Jenn-Air stovetop

  • Customer: felton from sunset LA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The original fan switch for down draft stove top was discontinued! I found a replacement switch which worked just fine! I received switch and 2 different type replacement plates! One an exact match! Switch different but worked fine! I had to make no modification! Changed I'm about 10 minutes! I was lucky from what I read on other customers' responses!! They wouldn't promise me it would work!!

Igniter not working

  • Customer: Casey from Soledad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4

The original filter was decomposing each time I washed it

  • Customer: Sharon from Kenai AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

2 burners rusted apart, 1 gas valve frozen up.

  • Customer: robin from saint marys GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.

Broke the insulator on the ignitor while cleaning the cooktop.

  • Customer: David from Shelley ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.

gas burner had rusted out

  • Customer: John from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced burner

Burner head was rusted through

  • Customer: Joellen from Castro Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This is the second burner head I have replaced. It was easier than the first time but the burner head I received did not have the screw holes to reattach the gas tube to the burner head. I was able to drill my own without too much trouble using a standard bit and electric drill. I used the old burner head to determine what size drill bit to use. Even so, it was still an easy fix.
All Instructions for the JGD8130ADS
61-75 of 82