Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JGD8130ADS

JGD8130ADS Jenn-Air Cooktop - Overview

Get Parts and Repair Help for JGD8130ADS

If you know the cooktop repair part you need, you can browse the list of all parts on the JGD8130ADS, or you can search by name or part description. You can also find your part by where it is located on the JGD8130ADS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for JGD8130ADS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$26.16

Grease Filter

The function of the grease filter is to trap grease into the filter from the exhaust air. The grease filter is intended to be used with certain downdraft cooktops and ranges. This ...

Order within the next 3 hrs and your part ships today!
$17.65

Top Burner Igniter

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

Order within the next 3 hrs and your part ships today!
$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

Order within the next 3 hrs and your part ships today!
$4.87

Burner Control Knob

Sold individually. This knob accepts a D-shaped shaft.

Order within the next 3 hrs and your part ships today!
$5.65

Bumper Pad Set of 4

***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cook...

Order within the next 3 hrs and your part ships today!
$84.28

Burner Head

The spark igniter is sold separately.

Order within the next 3 hrs and your part ships today!
$4.63

Brass Seal

Order within the next 3 hrs and your part ships today!
$99.01

Grill Grate

This grill grate is sold individually.

$38.32

Spark Igniter Set

This part provides the spark to the burners.

Order within the next 3 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replaced filter

  • Customer: ELOISE from MILFORD, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 474 of 485 people found this instruction helpful
pulled old one out , cleaned the area & replaced with the new one. read more

Old grease filter that I actually did not know I had to change

  • Customer: deborah from fort pierce, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 443 of 523 people found this instruction helpful
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 123 of 137 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more