JEW8530AAW Jenn-Air Wall Oven - Instructions

My husband ( a superior handy man) very easily replaced the glass on the inside of the oven door and further replaced the hinges which had sprung yrs ago when I rested a 30+ lb turkey on the door. He removed the oven door and it was obvious to him how to repair the problem. The oven is back to heating correctly.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

The display belongs to the convection oven. We still could use the oven because we knew how all the buttons and beeps worked, but we replaced the control module because we couldn't sell the house without it. Here's how to replace the module:
- Remove the bezel on the microwave above the oven (4 screws on the sides).
- Now you can remove four up-facing screws on top of the control panel. Don't unwire the panel, just lay it face-down on the topmost oven shelf, as one of the others above advised.
- Looking at the back of the clock module, remove the two connectors. The larger one is difficult to pull. Just force each end gently straight up with a flat screwdriver.
- Remove the screws holding the clock in place. They're at the two ends.
- Swap the clocks and put everything back.
I bought this module from PartSelect because of all the customer feedback you see here. It gave me the confidence to do it myself.

very easy

Screwed in light bulb and glass protector

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

ordered new broiler pan

Took the door apart and replaced the hinge, very easy

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

First, there are NO instructions on how to replace the glass on this type of oven door! Nothing came with the replacement glass and we could not find anything on the internet for this model. The oven door hinges are like no other oven door. There is no hinge lock and you can't just remove the guard plate and lift the door off the hinge. I ended up with a smashed finger because the hinge slammed shut before I could move my hand. The oven glass is STILL not replaced and we are having a heck of a time trying to find an expert to come to our home to fix it.

We had a wood tray in the oven (yes i know) and it is a two stacked oven and turned the wrong oven to broil. The fire was put out quickly but the Latch door switch and assembly was damaged.
The 3D breakout of the appliance made it a jiffy to select the correct part numbers. Shipping is very good from Parts Select.
The Front assembly for the lower oven comes out with 6 screws. Disconnect the Door Switch Connector push it out and replace that. The Latch Assembly requires a small wrench. It is a bad design but patience will get you there. Once the assembly is out disconnect electrical connectors. Don't worry each connector is unique I advice do it one for one.
Overall you need a skill of three stars out of five to complete this task

I followed the great directions posted by others on the PartSelect website for Part No. PS2078472. This was really easy! Another customer has posted a GREAT suggestion of pulling the top oven shelf out about a foot and using it to lay the control panel faceplate assembl on after its unscrewed and lifted off its support. I used (and suggest others use) a soft cloth to put under the control panel before I laid it on the extended top oven shelf to avoid any scratching. I took great comfort from the prior 9-28-07 posting by customer Cheryl from Mesa, AZ, in which she said that she was a "63 yr. old woman" and that the repair was "very easy" for her -- Let me add that it was also very easy for a slightly younger, but mechanically challenged man! PartSelect got my part right out to me (with a couple of replacement bulbs for the interior oven light, since my oven bulb had also just burned out). Everything was just as represented and I felt I got good value for the money. It's a pleasure to do business with PartSelect! Thanks also for making me a hero with my wife -- now she thinks I can fix things!